KUDC03ITBS3 KitchenAid Dishwasher - Instructions

Be sure to shut the power off before you attempt this first step, there are electrical connections all around this area. At first I didn't realize to get at the door handle I only to remove the top four screws on the inside of the door. After figuring this out the job was fairly easy. Once inside the top part of the door, all I had to do was snap off the old handle and snap in the new one. Test it to see if it works before you shut the door.

Just replaced the original cap with the new one. It fit perfectly. Thanks.
P.S. - I would rate this excellent. I would give it 5-stars.

I peeled off the old seal and replaced with the new seal. The instructions were clear and easy to follow, however the new seal made the door not stay closed as the friction catch at the top was no strong enough to overcome the tension of the door closed with the new seal.

There were explicit instructions on the way the seal was to work with the sealed edge spreading into the tub area as the door closed. I was very careful to follow those instructions and made sure to seat the seal carefully. After I reinstalled the seal three times to see if I could get it to seat properly, as a last ditch effort I reversed the seal to the opposite way the instructions indicated and it worked with the door closing properly and the seal didn't leak.

Based on looking at the old seal and how it was originally installed, I actually think the seal was out of spec for the unit. However, if it isn't leaking that is what it's all about so we will see how long it holds.

The repair was really easy. First disconnected electricity staring with fuses and removing wires from dishwasher, then disconnected drain hose and water hose. Pulled it out and removed pump turning clockwise no need for tools and same way installed new one. Very easy

Pulled everything out the front, and dug down to find a thrashed chopper assembly (like a little garbage disposal). The previous owner just tossed anything in; pop tops, plastic cutlery, etc.
Didn't pay attention to the exact installation of the chopper as I pulled it out, but, it turns out that it only goes in one way.
Used pictures and instructions I found online as a guide and didn't have any issues.
Replaced the check valve because it isn't expensive and I was in the neighborhood.

I found instructions on line when I goggled my dishwasher name and model number with the words noisy door. There were three or four good suggestions at a couple of the sites I visited. I tried applying vasoline, then silicone to the rope where it travels through the plastic guides but that just cut the sound down about 50%. My dishwasher has plastic guides that look like rollers but they don't turn, they are fixed in place. The ropes squeak as the pass over the guides. The replacement part kit has plastic guides that turn like wheels now so the rope does not drag over them and squeak. This repair could be done by me in 20 minutes or less every time now that I know what I am doing.

I removed the black bottom metal cover then turned the nuts on the adjusting (leveling) bolts to lower the front end of the dishwasher so I could pull it out of the cabinet. Once I lowered is as low as it would go I opened the door and pushed down on it which tilts the dishwasher down and you pull out on it and the top lip clears the cabinet. If your dishwasher just pulls out the first time you try these steps may not be necessary.
Once the dishwasher is out the guides and rope are down at the bottom in the front by the door. It's obvious what to do to replace them.

1.Check the lines for any obstruction. Gunk can easily build up. I have used the dishwasher for approx. 10 years. I do rinse/scrap dishes prior to loading.
2. Drain all remaining water.
3. Unplug the dishwasher.
4. Grab a towel and proper screw driver. Unscrew the bottom protective plate. Remove the insulation plate.
5. The drain pump is located to the bottom left. Have your towel under it. Unplug it gently. Turn counter clockwise to remove.
6. Install the new drain pump (reverse order)
7. Return the insulation plate. Screw back the bottom protective plate.
8. Plug in

Remove upper tray and spray arm. Remove two screws retaining pipe for upper spray arm and overhead. Unscrew retainer on top of lower spray arm and remove. Gently rotate the upper feed pipe clockwise until pipe can be removed from lower pipe. You may then remove the lower pipe and bearing housing where the seal is. Reverse order for reassembly. I also replaced upper spray arm bushing. Very simple, remove one screw and the arm will come out.

Cut power and turn off water. Pulled the dishwasher out of the cabinet. Removed internal spray unit. Lay a plastic bag on bottom of tub in case a screw falls from upper spray assembly while removing. Disconnected and drained all hoses. Put down plastic lined tarp on floor. Lay dishwaser on its side onto tarp. Removed hose from recirculation pump, removed water sensor and recirculation pump from housing and detach electric connection. Removed 3 plastic push clips and removed entire motor-pump unit from tub. Position new motor-pump unit into tub. Replace 2 push clips into position, then used a flat screwdriver to put some tension and position plastic pump assembly so I could insert 3rd push clip into position. Replaced all components & reconnect hoses. Turn on water & power. A relatively simple repair. Too bad the original motor-pump only lasted 3 years. Not built like the used to. Thank goodness for Part Select.com Great schematics and descriptions. Excellent website, service, delivery and excellent Part! Thank You!

1) Remove the racks

2) Unattach the feed tube the runs from the bottom of the dishwasher tub along the back to the top (this is the grey plastic tube that the top rack sprayer plugs into). This is done by unclipping the tube in two places, one stainless clip is in the back of the tub and one stainless clip is on the top of the tub.

3) After the tube is loosened from the clips, give the tube a 45° twist clockwise (relative to the bottom of the tub) and then pull up. This should remove the entire feed tube and bottom sprayer assembly.

4) There are now 4 stainless steel torx screws visible on the bottom of the tube. Remove the screws using a torx driver. Remove the grey plastic "gear looking" piece that was held in by the screws by pulling straight up.

5) On the left hand side of the tub you will see one more (smaller) torx screw. Remove this screw and then with a pair of plyers, give the housing piece that was held on with the screw a tug straight upwards. There is a post sticking straight up that will help you do this.

6) The grinder assembly is now visible, and in my case, completely jammed with paper. Pull the grinder and screen out of the groove it is sitting in.

7) Place the new grinding and screen into the groove. The grinder blade will have to be pull back (toward you) so the grinder coupling teeth can properly engage with the motor coupling teeth. This may take some fiddling.

8) once the grinder is installed, reverse all the steps starting at step 5.

very easy, thank you for your quick service

I looked up the most common problem with this model and it was the chopper assembly. I removed everything down to this. Sure enough, mine was broken off and the screen was completely clogged with debris. It was not difficult to replace, but it did take me a few minutes to slide it in to place. Ladies, you can do this. No need to call a repairman! Look up the repair manual and see where the assembly is. I had no idea it was even there. My dishes are spotless now.

Disconnect the water supply, the drain line, and the two screws that go up into the cabinet frame, then pull the dishwasher out from under the counter. Tip the unit onto it's face and the main pump/motor is facing up. Turn off the power then unplug the electrical connector from the motor. Remove the single bolt at the base of the motor then turn the whole motor ~1/4 turn counter-clockwise. A firm pull will remove the motor/pump at this point.
The new motor/pump has a new seal. See that the arrows on the pump volute and the motor frame are lined up before inserting into the housing. The new motor/pump slides into the housing easily and a 1/4 turn clockwise will pull it in tight. Re-install the locking bolt and revers the rest of the steps to get running again.

After pulling the dishwasher out from under the cabinet, I found it underneath near the back right side. I disconnected the old thermostat, unscrewed the clamp holding it into place, put the new thermostat in, screwed it back in and replaced the two plugs. Then I pushed the dishwasher back into place, and it initially didn't work until I found an online forum that was able to identify the reset command for my dishwasher (for the WDT710PAYM4, press any three buttons in a sequence of 1 2 3 1 2 3 1 2 3. After completing that all the lights lit up, and I shut the door leaving it for half an hour) Once the reset finished, the heated dry worked like it was suppose to.

.The easiest way to complete the impeller and chopper motor replacement is to disconnect the power, water and drain line, remove the dishwasher from the cabinet, set the washer on its back.

From this point everything is visible, pump housing, motor, etc. and it's a matter of disassembly and reassembly. Make note or a drawing of where all the wires are connected so you reconnect them in the right spots.

Reinstall water lines and power and check for leaks before replacing shield or kick plate.