6651598999 Kenmore Dishwasher - Instructions

Removed the old mount from the upper rack. Removed the broken stem from the old mount that was attached to the arm. Attached the new mount to the spray arm. Attached the mount and arm to the rack.

Turned off electricity. Removed the interior door cover. Removed door switch. Replaced switches & reversed process. By the way - I am a woman & diagnosised, ordered part & fixed it myself - I have no experience in this field. THANKS for all your information on your site.

Very easy to snap in. I would recommend to make them more slippery to snap in. Maybe use a little soap or place them in hot water before you place them on dishwasher tray.

Removed 2 screws that held the old mount and washer arm in place, new mount was very easy to install, it snapped in, only one screw needed, remounted the washer arm and the job was done. I was really impressed with the ease of ordering and how quick it got here (3 days), also the scematics you have online are very helpful. I printed them out since I don't have the owners manual any longer, they're very helpful in matching up and ordering the right part which saves a lot of time, also I like the way you can just search by model number and appliance name to find the right parts, makes the entire process really easy. I know I will continue to shop here when the need arises. It really cuts down on expensive repair costs.

Hey parts select, I'm Julia's husband and the repair was a simple remove and replace. Only one screw to hold the manifold together and the mounting hardware that we had to order separately was a snap in piece which was different form the original but went in just fine. You saved me from having to buy a new dishwasher which Julia was more than happy to go shopping for!! Thanks!!

Install too less that a minute. Fit perfectly.

Once the covers under the door are removed, the check valve is visible (unless its too dark, hence the headlight), and pointing right at you. Since I was working under the dishwasher, I gathered all the tools I thought I might need and laid them on the floor next to. Removed 2 covers, placed pan under check valve and hose to catch any water, squeezed clamp with (wrong) pliers, it eventually came loose. Carefully twisted hose off check valve. Water came out, some of it got into the pan, most of it on the floor. I guess I should have pumped it out before I started this. Plastic check valve is screwed into the big piece of whatever, carefully grabbed it with (wrong again) pliers and turned it out. Installation is reverse of removal - but use a large pliers with a ROUNDED jaw to grab the round check valve body. Don't squeeze too hard or overtighten it. Put the clamp on the valve before pushing the hose on. Be sure the hose seats all the way onto the little lugs. Compress the clamp, slide it over the end of the hose and release. That's all folks, works good now.

Put in both a new element and thermostat. Did not fix problem. Using an ohm meter I did not measure any voltage to the thermostat. Suspect it’s a problem in the control unit, and decided to replace dishwasher.

1) Removed the two panels below the door.
2) Unscrewed the two screws holding the dishwasher to the upper cabinet facing.
3) Pulled dishwasher out 6-8 inches to gain access to springs located on the side.
4) Removed the broken spring.
5) Attached the new spring.
6) Openned and closed the door to make sure spring was tight enough.
7) Pushed dishwasher back in.
8) Rescrewed cabinet facing screws
9) Rescrewed floor panels.

Only problem was with ordering ... PartSelect part number is different than the FSP-Whirlpool part number. PartSelect should provide a cross-reference table if there is a difference between OEM number and PartSelect number.

First I read the other repair stories and knew it was a relatively easy repair. I removed the end caps on the front of the top dish rack and removed it for ease of access to the part. I then removed the two screws holding in the old part observing how it was positioned to make sure the new part was replaced in the same manner. I put the new part in place and screwed in place and replaced the dish rack. Everything is working just fine.

Took the bottom panel off and felt with fingers to replace spring with out pulling dishwasher out from enclosure.
Fairly simple

removed two hose clamps and old hose. slid new hose on existing fittings on dishwasher drain and disposal and tightened hose clamps. Turned it on for test run.

Great fit. take out old one and drop in new one. Piece of Cake.

At first I thought I needed a new bottom rack for my dishwasher. Out of curiosity, I watched the installation video and realized that the Tine Row installed separately and that was the only part I needed. I am appreciative of being able to access that video and the money I saved. Installation took seconds to complete.

I ordered the upper and lower rack replacements PLUS additional wheels and other attachments because I could not tell from the schematic on the website whether or not the smaller pieces came with the rack.

As it turned out, the racks came ready to install and all it took was a limber nephew to take out the old ones and put in the new. Now I have plenty of spare parts in my own inventory in case the wheels, etc. need replacing.

I feel guilty sending you this repair story because all I did was order the parts on your website and then conned my nephew into making the exchange.

The parts arrived very quickly and in good condition. In fact, the new racks are an improvement over the ones that came with the dishwasher originally. Ms. Susan McNutt was quite helpful in keeping me informed of the status of the part that was back-ordered. It was a pleasure dealing with PartSelect.com.