66513929K014 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Peter from LEBANON, NJ
- Parts Used:
- WPW10497235
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
door leaks bottom right
leveled dishwasher, it was leaning forward, raised front 1/2'", to get level.
no More leaks, WOULD LIKE TO RETURN DOOR SEAL. DID NOT USE SEAL.
THANKS,
PETE GODSHALK
no More leaks, WOULD LIKE TO RETURN DOOR SEAL. DID NOT USE SEAL.
THANKS,
PETE GODSHALK
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Mckinney, TX
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Door link broke at plastic connection end
First remove the front kick panel by removing 2 philips screws. Turn off the water supply, and then disconnect the supply line if not of the flexible kind. Mine was copper. Remove 2 screws holding dishwasher to counter top and pull machine out. Open door and attach replacement link by hooking the plastic end to the hinge hook on the door side and then place the string portion round the plastic pulleys and then attach the other end of the link to the end of the spring attached to the rear of the machine along the bottom side. Push dishwasher back into position, reattach supply line and re-install both screws attaching the machine to the counter top. Turn on the water supply and check for leaks. Place the kick plate into postion and secure using the 2 philips screws that were removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSEPH from LAMBERTVILLE, NJ
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Door falls when opened
Attached new link, then stretched the spring with pliers and routed link over the pulley. Replaced both links.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pauline from FERGUS FALLS, MN
- Parts Used:
- 8194001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
Broken plastic piece in door balance link kit
Watch video and followed instructions. Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from BIRMINGHAM, MI
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Dishwasher door had lost springback
1) Pull out dishwasher from under counter. 2) Disconnect spring located at the bottom on each side of dishwasher. 3) Using socket remove pulley wheels from each side at bottom. 4) Install new pulleys on each side. 5) Wind pulley cord around both wheels and attach to one end of the spring on each side. 6) Using pliers extend other spring end to lower frame of dishwasher on each side. 7) Open and close dishwasher door to test. 8) Replacement complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucille from MODESTO, CA
- Parts Used:
- W10619006
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Washer would not turn on
Watched a video and read through written directions.
Did not need to pull out the dishwasher from the cabinet.
Did not need to pull out the dishwasher from the cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from SOUTHAMPTON, PA
- Parts Used:
- 8193983
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Spinner broke off at interior top. (Little ball on bottom of spinner fell off.)
I am an 84 year-old woman so I asked another woman friend to help me. We removed both shelves from interior of dishwasher then unscrewed the first screw of the slim plastic piece on the top of the interior; then the second screw. We pulled the plastic piece gently down, removed the little round part out of the groove. We placed the new round part in the groove (ball down), pushed the spinner onto it so it would click on & hold. That required a bit of strength. Replaced screws & it was done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Highland Village, TX
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Door Leveler Nylon Cord assy broke
It was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ted from Santa Clarita, CA
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Broken cord on door balance
Very easy. I removed the two screws on the base plate, then the two screws that attach the washer to the cabinet, and pulled the washer out of its slot. I installed the broken side and closely checked the other side and felt it didn't need repairing. I put it back together and the door works very well.
Thanks,
Ted K.
Thanks,
Ted K.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from SOUTH HADLEY, MA
- Parts Used:
- WPW10497235
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
Dishwasher was leaking at the bottom edge of door.
Ordered the door gasket and replaced it. Worked perfect. The trick was to stretch the gasket a little as it went around the top curvatures. It would stick out some and not sit as flat as on the top and sides. This helped it to flatten down better.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Des Moines, IA
- Parts Used:
- 8269144A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Dish washer was very smelly.
After replacing garbage disposal. I referred to you video you sent me when i received the new replacement hose. That made it look very easy to install. Thank you for all your help and support.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- COLIN from SIMI VALLEY, CA
- Parts Used:
- W10402110
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
No power the thermal fuse had blown
I removed the door front, unclipped the PC board cover and removed the thermal fuse from its housing. I did not splice the wires per the enclosed diagram that came with the part but unclipped the fuse from the connectors and then clipped the connectors on the new fuse and slotted the fuse back on the PC board. Put the board cover back on and then the door front. Job done.
Was this instruction helpful to you?
Thank you for voting!
PartSelect Scammers
PartSelect intentionally shipped obsolete part that could not possibly fit a dishwasher. The part looked to be a rectangle door seal for a freezer/ref. You make it impossible to return the part. I find it interesting that you sent the correct install video and wrong part.
Suggestion: After you print a shipping label take a picture of the part and shipping label before it is boxed. The customer should not have to send you a picture of the wrong part and the serial number of the appliance for a refund. You did not need the serial number to ship it.
I will never use your company again William Dewberry
Suggestion: After you print a shipping label take a picture of the part and shipping label before it is boxed. The customer should not have to send you a picture of the wrong part and the serial number of the appliance for a refund. You did not need the serial number to ship it.
I will never use your company again William Dewberry
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from COOKEVILLE, TN
- Parts Used:
- W10648041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
Pin hole leak in valve body.
Kill power to unit. Turn off water supply. Remove front access panel. Remove screw holding valve housing. Remove valve. Disconnect water lines. Replace valve in housing. Reconnect water lines with addition of thread tape. Reinstall valve and housing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from sullivan, OH
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door of the dishwaher banged open
Pulled the dishwasher out and took the two door balance links off and put the new ones on and attached to the spring. It was very quick and easy
Was this instruction helpful to you?
Thank you for voting!