6651587981 Kenmore Dishwasher - Instructions

This is the second time I have replaced a rack. You just pop on the new rollers and you're good to go!

Just put it on by hand, works great now, saved me at least 50.00!

Ordered a new upper spray arm from PartSelect. Shipping was fast and the correct part was recieved.
Use a hair drier to warm the prongs that mount to the upper basket. The plastic is softer and will squeeze/fit in place without snapping off the "ears".

I layed the bottom rack upside down on the counter. Removed the old wheel sets and the new ones just snapped into position. I think the rack rolls better now than it ever did with the original equipment. I'm glad we purchase the Tandem Rack Rollers instead of a new dishwasher, it works great.

removed old check valve from bottom of dishwasher and replaced with new one. I used channel locks to do this, disconnect hoses and screw out check valve, and put back in opposite order, make sure the dishwasher is empty of water or have a plastic bowl or such to catch water. Take off two front covers on bottom of dishwasher to access check valve ,white with hose attached.

We took the rollers off the old one (new ones came with the dishrack also) and put them on the dishrack (they snapped on). There was also an extra piece that we figured out how to put on. Then slid it in place and it was fine.

Unsnapped old rollers and snapped new rollers in their place. Very easy. The new set fit perfectly.

Removed the washer from the cabinet, although the repair kit could have been replaced without this step. However, it still made it easier. Removed the spray arm assembly and the top cover to the motor. I had to block the motor to keep it from turning while I unscrewed part number 11. The rest was very self explanatory. The "impeller" was seized onto the motor shaft (20 years old) so I had to use a chisel to break what remained off, then clean some corrosion from the shaft. The repair kit worked and the pictorial parts diagram that came with the kit was very clear. Bottom line: "Easy peasy, lemon squeezy!" Great web site for diagnosis and parts diagrams!

The old spring on the detergent dispenser box door failed and the dispenser door would not pop open at the right time in the wash cycle.

Ordering the new spring was easy on the website. Need dishwasher model number, stock number and serial number.

Hint - Order at least 2 springs! They are not expensive.

I followed the instructions in the video. I could get the spring on the spindle correctly but could not get the two spring prongs to catch to create spring tension on the door without using a thin knife blade to carefully push each prong to where it caught on the dispenser door.

I needed to slide the prongs slowly and carefully to get them to catch on the door. This distorted the spring. That's why you really need two springs. I then used needle nose pliers to pull the latching part of the spring to catch on the inner door. That distorts the spring, too.

So you really need two springs. One spring to learn how to do it and a second one to replace the one you distorted as you learned.

Take care

First, I checked the ripped box for damage to the dishrack. Fortunately, there was none. Then I looked for the instruction booklet. Unfortunately, there was none. And the parts bag was ripped and I did not know what was supposed to be in it. So, I rechecked the photo of the dishrack on the website and found that either parts were missing or the dishrack was different than illistrated. After a few moments of thought, I realized the latter was the case. I then figured I would have to use some deep thought to do the installation since neither the missing instruction booklet nor the unzoomable photo would help. So, I pulled out the tall thin thingamabob from the old dishrack and put it in the new one though it did not secure as tightly. Then I put the wheel units on just like the old one. What I could not immediately figure out was where the collapsible rack row was mounted. I eventually realized that the rod went into a hole in the wheel units and the latch mounted above one unit. I still have no idea where the two other tan clips go. Though the dishrack is different and thus requires different science to fill it, it appears to do the job.

Thanks for asking.

By the way, it was not blue.

Unscrewed the nozzle cap, screwed in the new nozzle cap. What a snap! Sure beats a $75.00 service call and a parts bill that would be double what I paid!

removed the bottom panel 4 screws,then replaced the new springs. I bought two and left the other one inside the panel saved $80.00 servive call.

I bought the kit because it had other parts that I thought I needed.

It was a piece of cake, just slapped together and slid it into place!

This job took 30 seconds to accomplish. The old wheel assemblies (4) just snapped off and the new wheel rollers just snapped in their place. No tools were needed. Extremely satisfied with this product. Wished I had performed this repair years ago!