66513203N410 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from INVER GROVE, MN
- Parts Used:
- W10712395
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Three of the rack wheel axels broke on the top rack of the dishwasher
There were no instructions with the kit so I went online and watched a How-to video so I could fix it. However, the new white wheels were too big so I had to use the wheels from the old rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from MIDDLEBORO, MA
- Parts Used:
- W10728160
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Split tine row
Removed broken tin row. Replaced with new tine row. Tokk less than 1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from NEW HOPE, PA
- Parts Used:
- 8269144A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
A mouse was chewed through the hose and ate part of it. Di
Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from OXFORD, MI
- Parts Used:
- WPW10348269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
drain pump noisy, broken piece of glass caught in pump.
removed kick panel with screwdriver, 90 degree turn of screw. Put towel under drain pump. Disconnect drain hose by loosening spring clip with pliers to provide access to pump. released spring clip on old motor while turning counterclockwise to separate pump from drain reservoir. inspect drain reservoir from inside machine to remove any foreign objects. Installed new pump by indexing attachment flanges to notches in reservoir and turning pump clockwise until locking tab makes audible click. reattach drain hose insuring hose is contacting "stop" ribs on drain hose pipe. Run wash cycle on machine to insure there are no leaks. Re-attached kick panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from WAUKEE, IA
- Parts Used:
- WP8268961
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Friction sleeve came apart ....would not hold door in place
Pull dishwasher out a few inches. Disconnect spring from plastic connector with long nose pliers. Remove connector. Replace friction sleeve. Replace connector.Reconnect spring to plastic connector. This completes repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from IRVINE, CA
- Parts Used:
- WP8565925
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Roller wheel broke off upper rack and also end rack stops needed replacing.
Husband watched your repair video. Everything went well and we are very pleased.
Was this instruction helpful to you?
Thank you for voting!
Top rack wheel broken causing rack to fall when extended too far.
watched instructions and proceeded. Parts were self evident after watch ing video. Easy replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from WILMINGTON, DE
- Parts Used:
- WPW10350382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
transfer wheel racks, rack height adjuster and upper wash arm to new rack
The repair was similar to the very good video provided by PartSelect. However, I did make a few changes. The new rack was slightly different in the front side compared to the old rusted rack. After I removed the old rack from the dishwasher, I placed the two racks side-by -side to make sure they were compatible. They were identical in the rear structure and overall size, so I proceeded to change out the wheel racks, rack height adjusters and upper wash arm to the new rack. I suggest transferring each part one at a time so you can get the spacing correct. Also, in my case, many of the items needed to be washed with water to remove soap buildup in these parts before moving to the new rack. I would also suggest putting the upper wash arm (needed in this case) on the new rack last. The total job took me about an hour including washing or rinsing all parts and reassembly. This is an easy job, just take your time and do one item at a time so nothing gets mixed up. I used a drill driver to remove a total of 4 Phillip head screws for the rack height adjusters but a regular Phillip head screw driver would work as well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from REIDSVILLE, NC
- Parts Used:
- W11086533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Needed a tub sound shield
All I had to do is lay the shield over the top and sides and used a couple of clips to hold in place as it was slid under the counter top. It couldn’t have been easier.We had searched everywhere for this replacement shield and parts select was the the only ones that had it. Very good service and fast delivery,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colin from Goffstown, NH
- Parts Used:
- WPW10653840
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door latch wouldn't close
Turned off power to the dishwasher. Removed the front panel via the screws on the inner wall of the door. Lifted and pulled out the front panel. Disconnected cable connections to fully remove the front panel. Pressed down on the latches to the left and right side of the door latch. Pulled out the door latch. Put in new door latch until it clicked into place. Reattached cable connections. Put the front panel back on with the screws. Turned back on power to the dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from VALLEY STREAM, NY
- Parts Used:
- WP8268961
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door was falling down quickly
Only one friction sleeve was broken. So I pulled out the dishwasher to see how the one on the other side went on. It was very easy to replace and I replaced both. Unit works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from SKYKOMISH, WA
- Parts Used:
- WPW10348269
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
dishwasher would not drain
Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.
Was this instruction helpful to you?
Thank you for voting!
Replaced the wheels and adjuster on the top rack
Came as a box of loose parts with no directions. New parts looked totally different from OEM parts (better than OEM) on the rack. Luckily I went to the Partselect web site and they had a great short video preforming the task. Was a 15 minute job after the video.. If you get the Upper Rack Adjuster Kit with the wheels watch the short video and it’s a breeze!!
Was this instruction helpful to you?
Thank you for voting!
Upper dishrack pull out wheels broke away from the arms.
Listened to the video from Parts Select which was on the part number where it was ordered from. It was a very well done video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from WESTERVILLE, OH
- Parts Used:
- WP8565925
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rollers broke off top rack assembly
Replacement parts from factory installed using u tube support video
Also replaced stop ends for top rack by removing old clip in to push down and lined up to secure in slots at end of rack, notice new plastic parts are installed by pushing hardware into slots downward until they clip into place
Also replaced stop ends for top rack by removing old clip in to push down and lined up to secure in slots at end of rack, notice new plastic parts are installed by pushing hardware into slots downward until they clip into place
Was this instruction helpful to you?
Thank you for voting!