66513203N410 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paul from FORT MYERS, FL
- Parts Used:
- WPW10348269
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dishwasher would not drain properly due to broken impeller in the pump. Could hear and feel vibration thru pump body.
Followed the easy how-to video from PS. It was as easy as changing a light bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Sultan, WA
- Parts Used:
- WPW10510667
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Dishes not getting washed but water draining and filling working
Remove dishwasher from under kitchen counter. Lay down washer on it's back using some towels or other soft material to protect floor. Disconnect plug from pump motor and to get to the hose clamp easily I had to remove diverter motor. Be careful and slide diverter motor out slowly as it needs to engage the disc when putting back together. This took most of the time since I had to orient the disc slot with the diverter motor shaft that has mating tongue that goes into slot. Install pump motor but use liquid dish soap as lubricant to get hose elbow and pump inlet to slide in mating parts. Be sure to lubricate with same on tang that fits into rubber slot. Tighten elbow hose clamp with proper pliers for job. Re-install diverter motor assembly. Inspect for any oops's and install washer back under counter. Hook back up to drain, water and electric power.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brad from ABILENE, TX
- Parts Used:
- W10537869
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The diverter motor was leaking
Actually, I found a video on Youtube with excellent instructions once you got past the really simple stuff like disconnecting power and water and drain.
I would recommend just finding a fairly similar model on Youtube and follow their directions. It was really easy.
I would recommend just finding a fairly similar model on Youtube and follow their directions. It was really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from POQUOSON, VA
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
Broken Heating Element
I turned off the power to the dishwasher, removed the kick plate, raised the front levelers, disconnected the electric to the appliance, turned off the water supply to the appliance, disconnected the water supply, disconnected the drain system from the garbage disposal, unscrew the appliance from the countertop, then I remove the appliance from underneath the counter. I then tilted the appliance back and then in screwed the plastic retainers that held the heater element in place, removed the old one, replaced it with the new one in reversed the whole process
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from AUBURNDALE, WI
- Parts Used:
- WPW10195039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
water fill overflows at times
thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from WAYNESBORO, PA
- Parts Used:
- WPW10376693
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
little tabs holding sprayer arm to to rack broke off
placed sprayer arm in position and twisted it into position, about a 1/4 turn, snaps into place. total of 15 seconds!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Giorgio from Savannah, GA
- Parts Used:
- 8269144A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench set
Drain hose broken.
Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from HUDSON, NC
- Parts Used:
- WPW10348269
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
pump not working
Looked on you-tube and it was so easy. Pump on bottom right. unplug pump and do a halfway turn. Plug the new one up and place the pump on, and turn halfway and its on. START your dishwasher
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LINDA from ROSEVILLE, CA
- Parts Used:
- WP8268961
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door had no resistance when opening it
You only need to pull it out about 6 to 8 inches and you don’t need to disconnect anything to slide it on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from ROTONDA WEST, FL
- Parts Used:
- WPW10503549
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
A plastic retainer pin for the bottom kick panel was missing.
simply line up the new pin with the rectangular slot in the kick panel and metal panel behind, slide the pin in and turn it with a flat blade screw driver.
NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.
NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.
Was this instruction helpful to you?
Thank you for voting!
Upper Rack wheel broke off /Front track stops replaced
The upper rack adjuster kit was replaced exactly as the video showed. I felt it was not very complicated and the new parts look more hefty then the original parts.
Front track stops was just a matter of snapping them into place.
Front track stops was just a matter of snapping them into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aaron from Aurora, IL
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Start light was flashing
Thanks to everyone for posting their experiences on changing the heater element. The most difficult part of the repair was getting the dishwasher out of the cabinet. I didn't know that I should disconnect the water line underneath the sink and this would make the removal easier. Also, because the copper water line going to the dishwasher was kinked, I ended up changing it with a flexible steel braided line.....much easier to install.
Once the dishwasher was out of the cabinet, I turned it over and easily removed the clips that held the heater element in.
I would definetly recommend people doing this repair themselves, it will save you a lot of money!!!!!
Once the dishwasher was out of the cabinet, I turned it over and easily removed the clips that held the heater element in.
I would definetly recommend people doing this repair themselves, it will save you a lot of money!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from Great Falls, MT
- Parts Used:
- WP3400918
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
two retainers broke and the main part fell apart
pushed the new retainers in the holes and we are set to go
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J Kevin from Pittsburg, CA
- Parts Used:
- W10728159
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rack tines were corroded
Took off the old wheels and placed them on the new rack - fast and easy if you watch the video.
Was this instruction helpful to you?
Thank you for voting!