66517152K216 Kenmore Dishwasher - Instructions

After reading customer notes regarding the same problem I was having I ordered A new Heater Element & a High Limit Thermostat. I also ordered a Heating Element Nut and Rubber Washer in case I needed them. It took me quite some time to remove the dishwasher from under my counter. Once the unit was out and prepared to service it actually took only a few minutes to install the new Heater Element. I did't need the washer or extra Nut. I also decided to try the unit without replacing the thermostat. I cleared the diagnostics by pressing the "HEATED DRY, "NORMAL", "HEATED DRY", "NORMAL" buttons. After the controller reset the dishwasher was ready to run.

It is a small plastic piece which serves as a stop on the right side of the upper rack. It is the correct part because it is identical to the left one of the same type. I tried clamping down with a pair of pliers but I am afraid of breaking it. With shipping this two inch piece of plastic cost $20, so I do not want to crack it. I am at a loss as to how to sit in in place.

Pulled dishwasher out of compartment, removed all parts underneath. removed inner parts, removed pump assembly. Installed new pump assembly and grommet. Reassembled in reverse order, test ran and unit was operating normal and no leaks.

Could not take apart the upper rack on my whirlpool dishwasher to replace its wheels to transport its upper rack. The received parts did not match the old ones. Called parts and they suggested these new parts remanufactured and changed from the old ones but they had not been notified. Brought to professional mechanics and they figured it out. Bullshit parts company!!

First i turned off the water and the power, then removed the two screws to the access panel under the door. Then remove 1 screw to the electrical box and removed the wire nuts and pulled the cable out of the box. Then disconect the water supply which is up front, but very little room to work. I didn't have to diconnect the drain hose because it was long enough for me to pull out the machine. After removing to screws that hold the machine to the counter you can pull it out. Remove 2 wire from the terminals of the heat coil. Unscrew the plastic nuts from the washer and remove. Assemble in reverse order and check for leaks. I tested the old element as well as the new element for resistance before installing.

removed unit from cabinet disconnected water and drain lines replaced heater very easy to do it took more time to remove unit from under counter than replace heater piece of cake..

Removing and installing the new part was fairly simple. We removed the water hose first since it is the easiest to see. We then removed the screw holding the part to the metal frame. We slid out the part out of the holder to remove the black hose and electric plug (it is like the old phone jacks). After it was completely off we plugged in the electric to the new part which was very easy since it can only go in one way. We slid the new part in place and attached the black hose. We attached the piece to the frame with the one screw and last we attached the gold (garden hose) connection. We turned on the water to look for any leaks then turned the power on and ran it through a partial rinse to be sure there were no leaks.

Replaced the pump.That wasn't the problem --- if I had it to start over, I'd pull the drain hoses and run the dishwasher to see what water is flowing where. I had a clogged drain --- and maybe something else. Still working through the details.

I manually attached the track stop to the right track in the disheasher.

Husband watched your repair video. Everything went well and we are very pleased.

I had to replace the whole sliding system on the top rack. Plus the clips holding it. It snapped. I watched the video and did the steps from Steve. The rack slides better than when brand new. Whirlpool wouldn’t pick up phone but part select did. So thank you for being there so I could fix the rack and be able to use the dishwasher again.

1. Open dishwasher door, to access the screws holding dishwasher to cabinet.... remove these screws.
2. May need to shut water off and unscrew water line and waste line (if they aren't long enough because you will need to pull dishwasher out.
3. Unplug electricity
4. Pull dishwasher all the way out... probably need to disconnect the water and waste lines
5. crescent wrench to unscrew the plastic screws in back
6. Disconnect two wires going to element
7. Replace element... reverse steps
8. Not too bad at all
9. Part Select is Awesome !!!!

Our dishwasher's top rack would pull too far out which made it hard to stay in alignment. It had lost it's track stop. I easily ordered the part from PartSelect, and it came more quickly than I expected; I clicked it in place and it runs like new. It's wonderful to deal with a company that knows the frustration of not having your appliance in good working orfer.
Thank you.
Sue M
Masdsachusetts

Very easy,take off the old faucet screen and screw on the adapter. What I really liked was the ease of ordering the part. In less than 5 minutes I had located the part and ordered it. Less than 3 days later, I had the part. Way to go PartSelect.

Remove and replace by hand, no tools required