66513283K117 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Walter O from CROYDON, PA
- Parts Used:
- WPW10348269
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dishwasher would not empty.
Ordered a new pump (after a online diagnosis). Followed the instruction video on the website...also took the time to replace the discharge hose due to residue buildup...tested dishwasher (one cycle). Slide dishwasher back into opening....DONE. Works perfectly. THANKS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from MIDDLEBORO, MA
- Parts Used:
- W10728160
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Split tine row
Removed broken tin row. Replaced with new tine row. Tokk less than 1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from Great Falls, MT
- Parts Used:
- WP3400918
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
two retainers broke and the main part fell apart
pushed the new retainers in the holes and we are set to go
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from SUSANVILLE, CA
- Parts Used:
- WPW10491331
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The filter came out and pushed the arm up on the burner and melted it.
The air just unscrews with one twist and the new arm twist right back on. No tools needs. Saved me $100 service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Tucson, AZ
- Parts Used:
- WPW10327249, WPW10195039
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door leaking
Float switch right in front. Did not remove dishwasher. Used small flat screwdriver to un clip cover. Very soft and easy. Unplug and it slides out.
Same with the water inlet. Did not remove and used a screwdriver and small channel locks. Turn off water. Remove hose and remove screw. Slides out. Very easy.
Same with the water inlet. Did not remove and used a screwdriver and small channel locks. Turn off water. Remove hose and remove screw. Slides out. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggy from Sallis, MS
- Parts Used:
- WPW10195622, W10712394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The rollers on my top rack in my dish washer were broken and wouldn't stay on every time you pull the rack out it would fall. So I ordered the rack adjuster kit and it had everything I needed to fix it. Works like brand new now not hard to change and put new on took about 15 minutes approximately. D
Just remove from dishwasher the top rack and remove the old rack adjusters and put the new ones on , only 2 screws to each side and you are back in business. Very easy to change out. Put the rack back in slots in dishwasher and that's it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maynard from WISDOM, MT
- Parts Used:
- WPW10348269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Would not drain water
Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from WAUKEE, IA
- Parts Used:
- WP8268961
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Friction sleeve came apart ....would not hold door in place
Pull dishwasher out a few inches. Disconnect spring from plastic connector with long nose pliers. Remove connector. Replace friction sleeve. Replace connector.Reconnect spring to plastic connector. This completes repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from ALTOONA, IA
- Parts Used:
- WPW10195175
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
it was the detergent dispencer, we had to install it twice. and it still does not work
like the instructions showed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from BUFFALO GROVE, IL
- Parts Used:
- W10727426
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
Broken tine rows on upper basket
Popping out the old tine rows was very simple and required no tools. The only issue was that the spacing of the replacement tines was different from the original parts and there was not enough space between the tines and the basket to snap the clips back on to hold the tine row. I went to my band saw and cut the extended ends off of the clips and then they snapped into place perfectly. This would have been a 20 minute, no tool job if I didn't have to run to the band saw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from PROSPECT HTS, IL
- Parts Used:
- W10712394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Original upper tray had broken away from all 4 rollers.
Although the b&w photos spooked me a bit. I quickly learned to tear off/break off the old adjuster arms, and then refer to the written directions for installing the new parts. Don't waste your time trying to figure out removal of the original parts, just get them off. So, I did not find the photos helpful, but I figured it out.,with help from the text And of course, once you do one side, the other side is a breeze!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from DALLAS, TX
- Parts Used:
- W10712394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Upper rack wheel broken
The pictures in the instructions supplied were horrible. I found a video on You Tube that made the install easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryca from TULSA, OK
- Parts Used:
- WPW10653840
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Dishwasher door stopped latching properly.
Initial inspection of the issue and research suggested the door latch was malfunctioning / broken. I bought the part and expressed it home. The installation involved removing the door screws on the inside of the door, separating the front and back panels, unplugging the door latch, removing it from its niche and popping in the new one. Reverse the take apart and it was done. Very simple swap. Hardest part was juggling the two halves of the door and preventing the door for trying to close in the process as the bulk of the weight is in the outside half of the door.
The new part did not fix the issue. The door strike was the next part that could be broken / malfunctioning. I ordered that part as well and replaced it. In the process of replacing it I found that the original door strike had been installed upside down. I am guessing it was installed at just the right pitch, or maybe even bent at the manufacturing facility, so that it latched. No idea how it managed two years like that. I installed the new one correctly and the door latches perfectly. Both parts I removed from the unit I will retain if my new parts should fail in the future.
The new part did not fix the issue. The door strike was the next part that could be broken / malfunctioning. I ordered that part as well and replaced it. In the process of replacing it I found that the original door strike had been installed upside down. I am guessing it was installed at just the right pitch, or maybe even bent at the manufacturing facility, so that it latched. No idea how it managed two years like that. I installed the new one correctly and the door latches perfectly. Both parts I removed from the unit I will retain if my new parts should fail in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from VICKSBURG, MI
- Parts Used:
- WPW10195840
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
A plastic part on the top rack of my 2 year old dishwasher broke. Automatic dishwasher soap is corrosive and plastic parts should not be used in a dishwasher in the first place
The 1st person i had contact with wasn't any help choosing the correct part. Paid about $30.00 for the wrong part. Paid $8.00 more to ship the wrong part back for reimbursement. Meanwhile my son went to a local repair shop and got the right part for less than $40 and the repair shop installed the part on the rack for free
I was not happy with Part Select! Part Select cost me time and money and didnt get the job done
I was not happy with Part Select! Part Select cost me time and money and didnt get the job done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lenora from EMMETSBURG, IA
- Parts Used:
- WPW10195622
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Left side rack clip came off
I took the top dishwasher rack off, then took off the old clip I had taped on. I hadn’t watched the video so I put the new one on by looking at the other side rail and inserted the new part matching the other rail, clicked the new clip on and I was done. it was quite easy for an eighty-one year old woman!! It did take me awhile to figure it out.
Was this instruction helpful to you?
Thank you for voting!