6651687581 Kenmore Dishwasher - Instructions

A VERY easy repair! I simply pried off the old wheel assemblies with a screw driver and popped on the new ones. I was a little concerned about the new ones fitting correctly as the dishwasher is over 25 years old, but after a week they still work fine. An easy fix to an annoying problem....wish I had ordered these ages ago! Bottom rack of my dishwasher now rolls in and out like new (instead of the the few remaining wheels constantly falling off!) Very happy I ordered these and delivery was quick.

Unscrewed the old one and replaced it with the new one. My wife actually ordered this Pat and repaired the dishwasher.

Turn off the breaker to the dishwasher - there will be water very near the motor and other electrical components. I first scooped and towelled all the water out of the bottom of the dishwasher. The drain valve can be accessed from the bottom front of the dishwasher without pulling the unit out from under the counter. There were 4 screws to remove the 2 bottom metal panels. Next use pliers to loosen and slide back the hose clamp connected to the drain. Have a towel ready and pull the drain hose off the white check valve. The check valve can then be removed by unscrewing it - you may need to use pliers. Put the new one on and everything back together.

popped off the old rollers + tracks; then snapped on the new ones; as my granddaughter would say "easy peasy lemon squeezy". Took hardly any time at all. :-)

I reviewed your video and followed the steps, I appreciate the video. I used the tools described in the video; it was a simple process. Thank you Parts Select. .

My husband took the dishwasher apart three times, it was a little frustrating, but was worth the $50 part because it made his wife, very, very happy! A dishwasher operating is on the top 5 list of favorite electronic items in our house.

Very easy. Slide the dishwasher out a few inches, install spring per the good instructions, and slide the dishwasher back. Service was amazing. Part arrived just over 24 hours after I made the on-line order. I will use Part Select for all my future appliance parts needs.

Received new rollers promptly as ordered. Removed the old ones by snapping them off and simply snapped the new ones on. Took less than 5 minutes and job was a complete success. Wife happy and I am safe for now

The repair was simplicity itself. Remover the sprayer arm, removed the torx screws, replaced the seal, and reversed the process of disassembly. When I found out where the dishwasher was leaking from, I called KitchedAid and was ready to replace the overflow float. The part was 42.00 and wouldn't have fixed the problem. When I found this web site and read other peoples experience, I checked the pump seal, and it was obvious that it had blown out. That saved me a Loy of time and money.

As there was not a replacement gasket listed in the parts lists or schematics, I ordered the entire nozzle cap hoping the gasket would come with it. It didn't so I glued the gasket in place and installed the new cap. I also replaced the washer arm bearing while I had the cap off. I am hoping the nozzle stays in place.

Watched "Steve" install the drain and wash impeller kit and then I did it.

I watched the video then followed the procedure accessing the impeller/grinder from inside the tub. Had I not watched it, I would have torn into it from the bottom by removing the motor, etc. with disastrous results. I was quite depressed when installation of the impeller kit did not resolve the problem. I remembered from the survey that 56% of problems were solved with this kit; BUT, another 24% found that the check valve on the discharge line was the problem. So I removed it and lo and behold, it was partially plugged with broken pieces from the old impeller. The 1 page sheet that comes with the kit is simply a diagram of the parts included, there are no instructions ---- watch the video!!! All said and done, my experience with PartSelect was first class. They are 5 Stars in every category and I would highly recommend them.

Replaced the lower seal, drain impeller,chopper blade, and wash impeller. Problem is still not solved but the inner parts have been replaced. Only thing logical next is the check valve. Unit cycles well and if I turn the dial to just before the rinse cycle and watch, I do see water draining from the unit...Of course while replacing these parts, I checked other things and found a loose spring behind the front cover. It can be seen on the diagram as it is part of the detergent door mechanism (or so I believe), but it is not clear on where the spring actually connects to.

My soap dispenser latch was coated in grit, the gasket was deteriorated, and the spring was barely strong enough to open the door, so the door didn't always latch closed or open when it should. I followed the video and everything went exactly as shown. Once the liner was removed, I discovered the back (including the latch mechanism) was covered in soap residue and other gunk. I hosed it off on the backyard and resumed the repair. The dispenser now latches easily and opens with a convincing SNAP. I wouldn't have known how to replace the latch without the video. Great website!

We followed the excellent video until we couldn't remove the outlet impeller because the motor shaft was not being held by the failed impeller. We drilled small holes around the impeller shaft until we could break off the upper part of the pump shell. Then we could hold the motor shaft with a vice-grip pliers by squeezing the shaft of the remaing impeller piece. We then removed the retaining screw and the rest of the impeller. Then evrything went well by following the video. There was still a bit of doubt because we discarded more old parts then expected but the machine now works well and we see no leaks.