66515934000 Kenmore Dishwasher - Instructions

Several hours to diagnose problem: Removed all the plastic water distribution tubes to top rack and found no blockages. removed lower water jets, drain screens using star driver on 6 screws. still could find now blockages. decided problem had to be in pump mounted below unit so completely disconnected unit and removed from under counter. Upon removing lower plate below door I discovered a plastic pouch containing an excellent trouble shooting guide with complete dis-assembly instructions and parts breakout diagrams with P/N listings! First thing I discovered from this was that the chopper assembly was hiding under a plastic cover just under the filter screen I had already removed. The trick was to press down on the right side of the plate to get it to pop up and reveal the chopper. The whole chopper assembly slides out without tools. I found the strainer plate behind the chopper blade totally plugged as the blade had broken off the plastic drive shaft because the retaining knob on the end of the shaft had broken off. I was able to drill and tap the shaft and install a SS machine screw with washer to reassemble the chopper blade on the shaft. Not expecting this "Joe Maggee" repair to last more than a few cycles I went online with the P/N and googled PartSelect. Placed the order and chose std delivery over 2day or next day since I expected the repair to last for the week. I put everything back together and the first load came out perfect! This was Sunday afternoon. Tuesday the part arrived at my doorstep! 15 minutes and the new part was in. My "Joe Maggee" repair is now in the junk drawer awaiting the next pistachio shell that gets run through the washer.

This site is wonderful..., thank you. Especially thanks to Nanette's detailed experience. The thing that gave me the most problem (and apparently Nanette, as well) was removing the lower round cover of the chopper assembly. Finally, some one on the internet identified the trick...put needle nose pliers in the screw-hole and pull-away. It came right out. Wish I could acknowledge the source but now can't find it.
Actually, the check valve was good, but I replaced it anyway. It was 10 times the trouble to replace than the drain pump. Wish I had started with the drain pump. By removing the drain hose, I stuck my finger in the hole and discovered the problem: the impeller was off of the pump and lying in the bottom of the drain. It was a simple thing to replace the pump. Press down on the locking mechanism and turn it to the left. When it was off, I could see that the check valve was in place and not a problem. (Of course by that time, I had already replaced it.) Good luck.

To empty the water in the dishwater basin, I pushed the cancel button and closed the door. I then turned the electrical breaker to the off position that supplies electricity to the dishwasher. I confirmed the power was off by attempting to start the dishwaser. I removed the metal plate between the dishwater door and the floor by removing the two screws. I removed the two screws that connect the top of the dishwasher to the underside of the countertop. I shut the water valve that supplies hot water to the dishwasher (mine was located under the sink). I disconnected the drain hose (plastic) by using pliers to loosen the clamp the holds the hose on the outlet of the drain pump (drain pump is much smaller than the pump that needed replacement). A towell is handy to soak up the water that comes out the hoses. I loosened the nut on the water supply hose (this was difficult because of lack of room)using a wrench and pliers. I opened the door on the metal box that houses the wire nuts for the electrical connection to dishwater, and I removed the wire nuts and the screw for the ground wire. Once the white, black, and gound wires were disconnected, I could pull the dishwater out. I also had to pull the drain hose out from the clips on the side of the washer to pull the dishwasher out into the middle of the kitchen floor. I flipped the dishwasher on its back. I removed the single bolt that held the broken pump motor to the dishwasher, and then the motor twisted counterclockwise and I pulled it out. The pump shaft would not turn freely with my pliers, so I knew the motor was broken. I removed the pump end (impeller) from the dishwasher by tapping it with my screwdriver. The impeller end came out along with a metal screen. The metal screen was 50% plugged, so I cleaned it and put it back in place. I wet the gasket on the new pump motor and slid it back in place while rotating clockwise and locking it in place with the tabs. I replaced the bolt that holds the motor in place and reversed the repair procedure to re-install the dishwasher. Be sure to run the dishwasher and look for any leaks. The last step is to replace the metal plate between the floor and door. While I had the dishwasher pulled out, I discovered another problem with the pulleys and strings that prevent the heavy door from flopping down, but I won't include this repair. The pump and motor must have been failing for some time because the dishwasher is much quieter now and the dishwasher is much faster. I am sure the plugged screen didn't help either.

removed both upper and lower racks. removed lower spray arm(left hand thread) removed "water delivry tube and upper spray arm. removed torx screws on pump cover. removed inner chopper cover. Chopper assy had come apart and was full of food crud. cleaned out and installed new chopper assy. kind of tricky don't force it. reassembled. tested OK.could tell sound of more forceful water pressure

Pulled dishwasher out from under counter. Relaced cord with plastic hook attaching spring to door. Very easy.

Very impressed with Partselect.com. Full schematic of dishwasher made it easy to select part.

Delivered in 1 day. Fantastic. Highly recommend

This unit was unique that whole motor assembly was held in its place by two plastic clip. The gasket had few rings that worked as place holder, although gaskets don't go bad often this model could be if it gets pulled alot and if motor assembly get pushed it will push up the gasket and cause a leak. Repair was simple, 1) take spray arm off from inside. 2) get under neath the dishwasher, take off wires so it would free up some room, pulled two plastic holder out, gently push the motor assembly up to the tub, 3) from inside the tub, pull up the assembly enough to get your hand under the gasket and pull them off. 4) Replace the gasket, align the assmebly and push down to snap in the gasket. 5) get under and push in two plastic clip back in, put wires back into its place. Back in the tub to push down the assembly again to make sure there are flush with surface. Put spray arm back on. Finished.

Started as dishes not getting clean and I observed that the top arm was not spinning and there was very low water pressure coming out of the jets. After making sure the water level was up to the bottom of the heating element and making sure the jets were not clogged I checked the filter and chopper. It was a little tough to get the cover off of the chopper but once I did I could see that the chopper scraper was broken off and the shaft was broken. The screen was all clogged up with stuff. Ordered a new assembly and put it in making sure to compress the spring and make sure the gears lined up. Now it is running great.
I think the Kitchenaid is the same as the Whirlpools.

First: Turn power to the Dish washer OFF, then remove the two panels at the bottom of the dishwasher.
Two: remove the Door face panel for easier access to the inlet-Valve.
Three: remove screw that holds Inlet-valve bracket.
Four: slide Inlet valve bracket left and back to get out of slots.
Five: Holding the Inlet-valve forward loosen and remove water line (copper tube nut / pressure fitting).
Six: Remove two wire clips
Seven: Remove platics hose (Spring Clamp)
Replace Inlet-Valve and reverse process///

Turned off water and disconnected line, then disconnected drain, turned off power and slid dishwasher out and turned turned upside down and removed hold down bolt ( it is a 3/8 head bolt) removed wire from motor and twisted motor assembly approximately 1/4 turn counter clock wise and removed old motor and seal assembly reinstalled new motor with new seal and rewired. Turned washer back upright and removed filter assembly and lower jet arm, removed cover for food disposal and reinstalled disposal blade back on pump drive reinstalled cover and filter assembly and jet arm. Slid unit back in place and anchored down to cabinet and turned water and power back on ran washer through a short cycle to clean any soap build up that was left inside and that was it, it all works just like new.

Replaced electronic control panel first which had an obvious defect (burned terminal). Still no power. Replaced fuse and works fine now. Took lots of reading to find out the dishwasher had a replacable fuse. Even the appliance store didn't know.

Via your web-site I was able to download the step-by-step screen-shot pictures. I was really surprised on how easy the detailed photo screen shots made the repair really easy! Thanks for making this repair a piece of cake. If I should ever need additional parts for any of my home appliances I will certainly order my parts through PartSelect.

First I removed the screw from the top water tube and then the upper screw from the vertical water tube at the back of the dishwasher. That gave enough flex to the tube assembly for access to the area I needed to get to, without having to remove it. Then I removed the old spinner retainer and installed the new one. I then snapped the spinner to the new retainer pin, put the tube back into position, and re-installed the screws -- and I was done.

We recently installed all new stainless steel appliances, and were considering replacing the dishwasher as well (4 yr. old Kenmore, in good condition, energy star compliant, etc.). We decided to try to find a stainless front panel instead, and Kenmore said for that model they only came in black and white. But after calling Parts Select, they cross indexed our Kenmore model with a Whirlpool model that did come in stainless, and we simply ordered that front panel. The panel fit perfectly, only requiring the removal of 10 screws, and taking the insulation foam from the old panel and installing it in the new, then replacing the screws. Very simple, and economical, fix for our problem. Thanks Parts Select!

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

I noticed some residue in the dishwasher so I decided to clean the chopper screen. I dismantled the screen and spray assemblies and removed the chopper. The chopper was extremely worn and the chopper washer/gasket was missing. I reassembled the parts I removed and as I was placing the screws in the screen assembly I dropped a screw into the impeller well. Since the screws are stainless I was forced to remove the whole motor assembly. Since I had to order a chopper I went ahead and ordered a motor assembly gasket for reassembly. The mistake I made was not ordering a drain valve at the same time for when I removed the valve to clean it the rubber separated. The dishwasher will not function without it. This is where PartsSelect really came through for me. The 2-3 day shipping came in 2 days and the drain valve which was really going to hold me up with standard shipping came the very next day! Way to go PartsSelect! Everything went back together just fine.