6651688583 Kenmore Dishwasher - Instructions

I ordered the parts on Fri. and they came on Sat. Thanks. I had to pull the dishwasher forward about 6". Then just put the springs on. They don't have much tension with the door closed. Easy. Thanks again.

Replacing the cup latch and dispenser cover was pretty easy. First, I removed the inside cover of the door of the dishwasher. Then I carefully removed the plastic covers/slides on the door, removed the broken cup latch and then inserted the new one. Replaced the plastic covers/slides, the reinstalled the inside cover on the dishwasher. Next, I removed the dispenser cover and installed the new one. It snaps off/on, by the way. It only looks like it slides on/off.

Received new rollers promptly as ordered. Removed the old ones by snapping them off and simply snapped the new ones on. Took less than 5 minutes and job was a complete success. Wife happy and I am safe for now

took off the old wheels and put on the new.couldn't be easier.

Old tandem rack for rollers popped off lower rack by applying a small amount of pressure. New tandem rack rollers look slightly different, but pop right in place. By replacing all four tandem rack rollers the lower rack glides smoothly in and out of the dishwasher. Entire replacement can be done without tools, by hand in less than fifteen minutes.

I removed the rack and then pushed down on the old rollers to remove them from the rack. I then installed the new rollers in the same location.

screw it in then hook up the hose.

Very easy. Slide the dishwasher out a few inches, install spring per the good instructions, and slide the dishwasher back. Service was amazing. Part arrived just over 24 hours after I made the on-line order. I will use Part Select for all my future appliance parts needs.

You need a properly sized hex (Allen) wrench to get the screws out. Basically simple: remover bottom roller tray, unscrew large plastic holding bolt, remove lower spray arm, unscrew bolts (be sure the wrench is sized right or you might strip the heads), and replace gasket; then reverse procedure. Chances are if the gasket was bad, it will be very obvious (out of circular slot and stretched).

Put on new door, making sure the spring was set to flip the detergent door open in order for the detergent to properly do the dishes

A VERY easy repair! I simply pried off the old wheel assemblies with a screw driver and popped on the new ones. I was a little concerned about the new ones fitting correctly as the dishwasher is over 25 years old, but after a week they still work fine. An easy fix to an annoying problem....wish I had ordered these ages ago! Bottom rack of my dishwasher now rolls in and out like new (instead of the the few remaining wheels constantly falling off!) Very happy I ordered these and delivery was quick.

Removed cover and broken spring ,installed new spring and cover.Did it all in less than 10 minutes

Turn off the breaker to the dishwasher - there will be water very near the motor and other electrical components. I first scooped and towelled all the water out of the bottom of the dishwasher. The drain valve can be accessed from the bottom front of the dishwasher without pulling the unit out from under the counter. There were 4 screws to remove the 2 bottom metal panels. Next use pliers to loosen and slide back the hose clamp connected to the drain. Have a towel ready and pull the drain hose off the white check valve. The check valve can then be removed by unscrewing it - you may need to use pliers. Put the new one on and everything back together.

popped off the old rollers + tracks; then snapped on the new ones; as my granddaughter would say "easy peasy lemon squeezy". Took hardly any time at all. :-)

My model was DU7600XS0. I disassembled according to the video and the parts diagram here. I found a piece of metal, a pebble, and a wrecked drain impeller. I cleaned out all the debris and began reassembly. I found that the chopper blade shipped with this kit has a lip and will not fit over the metal drain impeller sleeve on this model. It needs to, or else it will not screw together properly and the impeller will not be able to turn. My old one was undamaged, so I used that instead. Also, the large black wash impeller has a shaft that is longer than the original part and because of that, it would not screw on. Again, the original wash impeller was fine, so I used the old one. I replace the gaskets and screwed everything else back together. It works great now. No water is left after the cycle anymore and the sound it makes is back to normal. Money well spent on this kit!