66513133K700 Kenmore Dishwasher - Instructions

Partselect provided me with tracking information for my order, they also provided an installation video. So when I replaced the door seal it was a few minutes to remove the old seal and about five minutes to put in the new one and it was all done.Thanks to Parts select it was a piece a cake

I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.

Removed broken tin row. Replaced with new tine row. Tokk less than 1 minute.

I followed another story for the same repair. Worked great.

I followed the wonderful videos provided with the part and fixed the problem easily! I suggest making a separate instructional video on how to get the dishwasher out of the housing.

Take out 6 screws from inside door upper most screws to control panel, removed water safety shield 3 easy tabs to release, found old fuse removed , cut wire 1 inch from old fuse removed have to pull fuse out of its plastic holder put in new fuse matched up wires, they are color coordinated, black with white stripe, and one solid black striped wires and twisted them tight, and inserted them in new wire harness that came from parts select tighten them tide them all together and used black electrical tape on all the new connections put back together and it totally fixed the problem so happy saved alot of money not having to call a service repairman

like the instructions showed

Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.

removed kick panel with screwdriver, 90 degree turn of screw. Put towel under drain pump. Disconnect drain hose by loosening spring clip with pliers to provide access to pump. released spring clip on old motor while turning counterclockwise to separate pump from drain reservoir. inspect drain reservoir from inside machine to remove any foreign objects. Installed new pump by indexing attachment flanges to notches in reservoir and turning pump clockwise until locking tab makes audible click. reattach drain hose insuring hose is contacting "stop" ribs on drain hose pipe. Run wash cycle on machine to insure there are no leaks. Re-attached kick panel.

The first try didn't go well. The door didn't stay locked because the new seal was preventing it.
I pulled it back off for the second try and first I let it soak in the hot water for a few minutes to soften the rubber. Then I lubricated it with Vaseline and now the seal got in the grove easily and completely. I believe that that step was critical to ensure 100% success rate. After that everything was fine, the door locked properly, and, of course, there was no more leaking.

Due to the way I installed the appliance originally it was not necessary to disconnect supply water nor the drain connections. When the cord broke the spring came out of the point of connection to the appliance. It some "finagelling" to reattach the spring.After some "select vocabulary" it hooked into the correct spot and the rest was history.

There was no tools involved the part popped right into place. I received the part within two days from the date placed. It was great.

First remove the front kick panel by removing 2 philips screws. Turn off the water supply, and then disconnect the supply line if not of the flexible kind. Mine was copper. Remove 2 screws holding dishwasher to counter top and pull machine out. Open door and attach replacement link by hooking the plastic end to the hinge hook on the door side and then place the string portion round the plastic pulleys and then attach the other end of the link to the end of the spring attached to the rear of the machine along the bottom side. Push dishwasher back into position, reattach supply line and re-install both screws attaching the machine to the counter top. Turn on the water supply and check for leaks. Place the kick plate into postion and secure using the 2 philips screws that were removed.

After doing some research on the Kitchen Aid issues. I turned off the breaker. Remove the (6) #15 Torx bit screws from the inside upper panel and removed the outside control panel. I located the Bi-Metal Fuse. I turned the breaker back on.Took a Electric Meter and it showed power only on one side. I order the part (BI-Metal Fuse) from the company. Turned the breaker off to there dishwasher. Very easy to install. I cut and trim the (2) wires. Match the black wire with the white stripe to the exact same color code and do the same for the all black wire. Install one wire at a time and tighten down with a small pocket screw driver. Then use the plastic tie straps to secure the (Bi-Metal Fuse).Turn the breaker back on. You are good to go.

0) assure main power was off
1) Opened up the panel assembly according to the instructions and the partselect video using the torx driver.
2) snipped the wires from the old part
3) patched in the new part by twisting the wire ends, inserting them into the assembly and tightening the screws.

Had my dishwasher up and running again within 15 minutes.