6651588581 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ruby from Saint Marys, GA
- Parts Used:
- 675238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
missing part
screw it in then hook up the hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Newton, MA
- Parts Used:
- 675611
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken door spring
Very easy. Slide the dishwasher out a few inches, install spring per the good instructions, and slide the dishwasher back. Service was amazing. Part arrived just over 24 hours after I made the on-line order. I will use Part Select for all my future appliance parts needs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- perry from cynthiana, KY
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
detergent dispencer door spring and pin worn
I installed the opener spring in the direction it was needed to open the door then installed the pin. I placed the door in the position it goes and took a pair of pliers and squeezed the pin into the pin slot. the spring has to be forced into a tension position. I did this by sliding the spring to one side and forcing it into position, the other side is done the same way. works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Alton, IL
- Parts Used:
- 675611
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
One spring on a dishwasher door was broken
I simply looked at the remaining spring to see which notch it needed to be attached to. I went in very well using a long needle nose plier. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fernando from El Paso, TX
- Parts Used:
- 675806
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Dishwasher making a noise (lower area)
I reviewed your video and followed the steps, I appreciate the video. I used the tools described in the video; it was a simple process. Thank you Parts Select. .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Trafalgar, IN
- Parts Used:
- WP302711
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishes not clean and soap dispenser not completely rinsed out.
I looked in the bottom of the dishwasher after browsing the website regarding possible solutions. When I removed the bottom spray arm I noticed three screws missing from the pump housing. The loose pump outlet had allowed the seal to push out. Ordered-Normal shipping on the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudia from Alexandria, VA
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rollers were broken on original parts
Unsnapped the old rollers and snapped in the new ones. Worked great and easy. I was very pleased that the parts came so soon as well. Thank You, Ms. Cason
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Arlington Heights, IL
- Parts Used:
- 675806
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Leaking seals
Used the diagram and disassembled and reassembled.Used most parts that were in kit as it also fit other models and did not need all the parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Taylor, TX
- Parts Used:
- W11086533
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Unfortunately, a mouse had made its home on top of our surround insulation. For hygienic reasons, I replaced the surround.
1. Turn off the electrical switch that powers the dishwasher. 2. Open the door of the dishwasher and find the two phillips head screws that secure the top of the dishwasher to the kitchen counter. 3. Remove the screws. 4. Gently move the machine side-by-side a bit while pulling it out onto the kitchen tile (be careful, the water-supply hose, electric cord, and dishwasher drain hose may not be long enough to allow you to pull it out very far - don't break or kink the hoses). 5. Remove (pull off) the black plastic fastener located on the bottom/rear of each side of the dishwasher. 6. Remove the old surround. 7. Lay the new wrap in place and secure with the two plastic fasteners. 8. Push back into place, secure the two screws, check your hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrel from rosamond, CA
- Parts Used:
- WP8066018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lid Spring
Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Columbia, MD
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Soap cup latch was broken and dispenser cover was worn.
Replacing the cup latch and dispenser cover was pretty easy. First, I removed the inside cover of the door of the dishwasher. Then I carefully removed the plastic covers/slides on the door, removed the broken cup latch and then inserted the new one. Replaced the plastic covers/slides, the reinstalled the inside cover on the dishwasher. Next, I removed the dispenser cover and installed the new one. It snaps off/on, by the way. It only looks like it slides on/off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Fallon, NV
- Parts Used:
- 675806
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
Dishwasher wouldn't drain
Watched "Steve" install the drain and wash impeller kit and then I did it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARVIN from NESBIT, MS
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lower rack wheels broke off roller assembly
Old tandem rack for rollers popped off lower rack by applying a small amount of pressure. New tandem rack rollers look slightly different, but pop right in place. By replacing all four tandem rack rollers the lower rack glides smoothly in and out of the dishwasher. Entire replacement can be done without tools, by hand in less than fifteen minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Millbrae, CA
- Parts Used:
- WP302711
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water leaking from the right front of appliance
The repair was simplicity itself. Remover the sprayer arm, removed the torx screws, replaced the seal, and reversed the process of disassembly. When I found out where the dishwasher was leaking from, I called KitchedAid and was ready to replace the overflow float. The part was 42.00 and wouldn't have fixed the problem. When I found this web site and read other peoples experience, I checked the pump seal, and it was obvious that it had blown out. That saved me a Loy of time and money.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leo from Idyllwild, CA
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Several of the wheels for the lower rack had fallen off.
I removed the rack and then pushed down on the old rollers to remove them from the rack. I then installed the new rollers in the same location.
Was this instruction helpful to you?
Thank you for voting!