66513044K111 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Aaron from Aurora, IL
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Start light was flashing
Thanks to everyone for posting their experiences on changing the heater element. The most difficult part of the repair was getting the dishwasher out of the cabinet. I didn't know that I should disconnect the water line underneath the sink and this would make the removal easier. Also, because the copper water line going to the dishwasher was kinked, I ended up changing it with a flexible steel braided line.....much easier to install.
Once the dishwasher was out of the cabinet, I turned it over and easily removed the clips that held the heater element in.
I would definetly recommend people doing this repair themselves, it will save you a lot of money!!!!!
Once the dishwasher was out of the cabinet, I turned it over and easily removed the clips that held the heater element in.
I would definetly recommend people doing this repair themselves, it will save you a lot of money!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert R from FOLSOM, CA
- Parts Used:
- WPW10195840, W10712394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Roller mount broke Rack Adjuster
Took half hour to take off old Adjuster just trying to figure which things pop off putting on new one side 10 minute at the most
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from DALLAS, TX
- Parts Used:
- W10712394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Upper rack wheel broken
The pictures in the instructions supplied were horrible. I found a video on You Tube that made the install easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from Great Falls, MT
- Parts Used:
- WP3400918
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
two retainers broke and the main part fell apart
pushed the new retainers in the holes and we are set to go
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J Kevin from Pittsburg, CA
- Parts Used:
- W10728159
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rack tines were corroded
Took off the old wheels and placed them on the new rack - fast and easy if you watch the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from REIDSVILLE, NC
- Parts Used:
- W11086533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Needed a tub sound shield
All I had to do is lay the shield over the top and sides and used a couple of clips to hold in place as it was slid under the counter top. It couldn’t have been easier.We had searched everywhere for this replacement shield and parts select was the the only ones that had it. Very good service and fast delivery,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from WILMINGTON, DE
- Parts Used:
- WPW10350382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
transfer wheel racks, rack height adjuster and upper wash arm to new rack
The repair was similar to the very good video provided by PartSelect. However, I did make a few changes. The new rack was slightly different in the front side compared to the old rusted rack. After I removed the old rack from the dishwasher, I placed the two racks side-by -side to make sure they were compatible. They were identical in the rear structure and overall size, so I proceeded to change out the wheel racks, rack height adjusters and upper wash arm to the new rack. I suggest transferring each part one at a time so you can get the spacing correct. Also, in my case, many of the items needed to be washed with water to remove soap buildup in these parts before moving to the new rack. I would also suggest putting the upper wash arm (needed in this case) on the new rack last. The total job took me about an hour including washing or rinsing all parts and reassembly. This is an easy job, just take your time and do one item at a time so nothing gets mixed up. I used a drill driver to remove a total of 4 Phillip head screws for the rack height adjusters but a regular Phillip head screw driver would work as well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from VALLEY STREAM, NY
- Parts Used:
- WP8268961
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door was falling down quickly
Only one friction sleeve was broken. So I pulled out the dishwasher to see how the one on the other side went on. It was very easy to replace and I replaced both. Unit works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from EARLEVILLE, MD
- Parts Used:
- WPW10195623, W10712394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Rack was drooping, falling off wheels.
VIEW THE INSTALLATION VIDEOS. They made it clear and simple...wish every company did them...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from WAUKEE, IA
- Parts Used:
- WP8268961
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Friction sleeve came apart ....would not hold door in place
Pull dishwasher out a few inches. Disconnect spring from plastic connector with long nose pliers. Remove connector. Replace friction sleeve. Replace connector.Reconnect spring to plastic connector. This completes repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from SKYKOMISH, WA
- Parts Used:
- WPW10348269
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
dishwasher would not drain
Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from PROSPECT HTS, IL
- Parts Used:
- W10712394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Original upper tray had broken away from all 4 rollers.
Although the b&w photos spooked me a bit. I quickly learned to tear off/break off the old adjuster arms, and then refer to the written directions for installing the new parts. Don't waste your time trying to figure out removal of the original parts, just get them off. So, I did not find the photos helpful, but I figured it out.,with help from the text And of course, once you do one side, the other side is a breeze!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from MIDDLEBORO, MA
- Parts Used:
- W10728160
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Split tine row
Removed broken tin row. Replaced with new tine row. Tokk less than 1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggy from Sallis, MS
- Parts Used:
- WPW10195622, W10712394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The rollers on my top rack in my dish washer were broken and wouldn't stay on every time you pull the rack out it would fall. So I ordered the rack adjuster kit and it had everything I needed to fix it. Works like brand new now not hard to change and put new on took about 15 minutes approximately. D
Just remove from dishwasher the top rack and remove the old rack adjusters and put the new ones on , only 2 screws to each side and you are back in business. Very easy to change out. Put the rack back in slots in dishwasher and that's it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from OXFORD, MI
- Parts Used:
- WPW10348269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
drain pump noisy, broken piece of glass caught in pump.
removed kick panel with screwdriver, 90 degree turn of screw. Put towel under drain pump. Disconnect drain hose by loosening spring clip with pliers to provide access to pump. released spring clip on old motor while turning counterclockwise to separate pump from drain reservoir. inspect drain reservoir from inside machine to remove any foreign objects. Installed new pump by indexing attachment flanges to notches in reservoir and turning pump clockwise until locking tab makes audible click. reattach drain hose insuring hose is contacting "stop" ribs on drain hose pipe. Run wash cycle on machine to insure there are no leaks. Re-attached kick panel.
Was this instruction helpful to you?
Thank you for voting!