66513929K011 Kenmore Dishwasher - Instructions

I found instructions on line when I goggled my dishwasher name and model number with the words noisy door. There were three or four good suggestions at a couple of the sites I visited. I tried applying vasoline, then silicone to the rope where it travels through the plastic guides but that just cut the sound down about 50%. My dishwasher has plastic guides that look like rollers but they don't turn, they are fixed in place. The ropes squeak as the pass over the guides. The replacement part kit has plastic guides that turn like wheels now so the rope does not drag over them and squeak. This repair could be done by me in 20 minutes or less every time now that I know what I am doing.

I removed the black bottom metal cover then turned the nuts on the adjusting (leveling) bolts to lower the front end of the dishwasher so I could pull it out of the cabinet. Once I lowered is as low as it would go I opened the door and pushed down on it which tilts the dishwasher down and you pull out on it and the top lip clears the cabinet. If your dishwasher just pulls out the first time you try these steps may not be necessary.
Once the dishwasher is out the guides and rope are down at the bottom in the front by the door. It's obvious what to do to replace them.

The repair was really easy. First disconnected electricity staring with fuses and removing wires from dishwasher, then disconnected drain hose and water hose. Pulled it out and removed pump turning clockwise no need for tools and same way installed new one. Very easy

simple...a female did it!! Dealing with PartSelect was so easy...your was the only web site that made it super easy to find my part. Placed order and paid for it...part arrived the next day!! Sent web site link to hubby too. When we need parts again for any applicance in our home, we will check your site out first!!

removed old gasket, installed new.
No Leaks!!
Saved the cost of a new dishwashers

I first turned the power off to the dishwasher. I then used the star bit to loosen the screws on the sides and top. Note that the 4 top screws are longer than the side screws. Once the screws were loose I used a clamp on each side to hold the door cover in place. Once the screws were removed, I released the clamps, raised the door then lifted the outer cover off. I then peeled the insulation back from the top to expose the dispenser. I used a small socket to remove the screws for the dispenser. I released the plug with a small slotted screw driver. I then exchanged the dispenser with the new unit being careful to correctly reinstall the black cover over the top. I reinstalled the door cover, being careful to tuck the insulation back in place. I then installed the screws using the clamps to hold the door in place during the reinstall.

Snapped the old one off and snapped the new one on.

You need to pull the unit out to get access to the spring connected to the rear leg frame. Use the everything in the kit. The rollers are upgraded and will guid the cable better.

Purchase 4 roller wheel assemblies and installed them with only a screw driver to open the tangs. quick and easy and rack rolls smoothly inside the dishwasher. Rather expensive $58 per roller assembly and hopefully these last the lifetime of the dishwasher.

A Mouse friend had seen fit to chew through the original drain line. I used my Model Number, and was able to order the correct part . It arrived the next day. The job itself is fairly straight forward. You will need to access the rear of the machine. This may include shutting off, and disconnecting the water supply line. (Adjustable wrench). Mine is under the sink, on the "Hot" side. You may also need to un-plug the unit. (recommended) . A pair of (Pliers) will be needed for the spring clamp.

I searched for another dishrack that was compatible with our unit. After measuring and searching online I found Partselect website and placed the order. It was a very easy process. I bought the rack without wheels and just removed the ones from our current bottom rack and put them on the new rack.

I pulled the upper rack out of the dishwasher. I then removed the broken rack clip stop on the right side and reinstalled the new replacement clip. I then put the rack back onto the rollers and voila, the upper rack no longer fell down off of the tracks!! Problem solved and the replacement clip only cost $8.95!!

Removed old gasket, cleaned track thoroughly, then followed instructions from video on Part Select order form. Instructions very clear and precise. Getting the new gasket was a little tedious at the corners but take your time and work the gasket with your fingers as shown on the video.

After bailing out the unit, filled filter hole with a moderate amount of Dawn dish washing detergent. Ran dishwasher twice to remove all Dawn from the unit. Had to bailout the water (and suds) from the washer both times. After the dishwasher finally drained I inserted the new filter..

push the 2 retaining clips back with my fingers and slide off the broken roller piece. Slide the new replacement 2 roller piece into place and push up until the retainer clips click and lock.

I am a 61 year old woman and it took me a total of 2 min. max. Popped it into place and pushed in button that holds it..Taa Daa...perfect!