66513273K110 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Pooi from TORRANCE, CA
- Parts Used:
- WPW10195622
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Upper drawer rack stop clip broke caused one side fell off rail.
I followed the YouTube attached with PartSelect email invoice to fix it. I am very happy PartSelect sent repairing video instruction and took me less than 15 minutes to get it done. Awesome!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ginger from DONIPHAN, NE
- Parts Used:
- WPW10491331
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
top of spray arm separated from bottom causing not to hold pressure and spin
Pulled up old spray arm and snapped new on in place. Took less than a minute and no tools. Dishwasher is like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Southbury, CT
- Parts Used:
- WP8268961
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door is designed to stay in place when opened. Door should hold partial or fully open.
Unscrewed brackets from underneath counter that hold dishwasher in place. Pulled dishwasher out of cabinet to access door hinges (approximately 8 to 12 inches). Released springs from door hinge (not necessary to remove spring from hole in dishwasher frame). Did not have to remove old sleeve because they tear and fall off. Slipped sleeve over door hinge to groove where they sit on hinge. Note: pulling hinge away from dishwasher a little. helps to complete installation.
Reinstall spring over hinge and check that door will stay a partial open. Slide dishwasher back in place and install screws from bracket to underside of counter.
My dishwasher only had two screws under counter to hold in place. Some installations have screws at sides also.
Reinstall spring over hinge and check that door will stay a partial open. Slide dishwasher back in place and install screws from bracket to underside of counter.
My dishwasher only had two screws under counter to hold in place. Some installations have screws at sides also.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marc from Baltimore, MD
- Parts Used:
- W10542314
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Water leak at the bottom left corner of the door
If your are just a tiny bit "handy", you can do this job in about 30 minutes for $30. The rubber gasket comes off very easily from its location, just pull it off, than, using a small piece of wood, I used a shim, insert the new gasket in, an inch at the time, all around the frame. No more leak, and probably over $150 savings. A plumber or repair man would have charged $90 just to drive to my house, plus part & labor.
Thanks to PartSelect too, the part was delivered rapidly and the all ordering process was painless.
Thanks to PartSelect too, the part was delivered rapidly and the all ordering process was painless.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucille from MODESTO, CA
- Parts Used:
- W10619006
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Washer would not turn on
Watched a video and read through written directions.
Did not need to pull out the dishwasher from the cabinet.
Did not need to pull out the dishwasher from the cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kerry from PRNC FREDERCK, MD
- Parts Used:
- WPW10195622
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Upper rack wheels broke
Originally I ordered the rack stop clips but realized I needed the whole upper rack repair kit. It entailed pulling off parts and popping new parts on. Very easy and simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dan from Humble, TX
- Parts Used:
- WPW10477552, W10518394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The green "Clean Light" was staying on after shutting down in the middle of the cycle. I put it in troubleshooting mode and found out it was the heating element.
Disconnect power Pull out dishwasher. Turn it 45 degrees to your right. Turn it on its side. disconnect the connections to the heating element {2}. Remove bolts, remove element. Install new element and tighten bolts. Reconnect electrical connectors. puch it back in place. reconnectPower your done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from MILWAUKEE, WI
- Parts Used:
- W10518394
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dishwasher would not start & green "Clean" light was flashing
After reading customer notes regarding the same problem I was having I ordered A new Heater Element & a High Limit Thermostat. I also ordered a Heating Element Nut and Rubber Washer in case I needed them. It took me quite some time to remove the dishwasher from under my counter. Once the unit was out and prepared to service it actually took only a few minutes to install the new Heater Element. I did't need the washer or extra Nut. I also decided to try the unit without replacing the thermostat. I cleared the diagnostics by pressing the "HEATED DRY, "NORMAL", "HEATED DRY", "NORMAL" buttons. After the controller reset the dishwasher was ready to run.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Toms River, NJ
- Parts Used:
- W10482988
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
When dishwasher went from water fill to power wash the dishwasher would shut down and the front lights would flash
I had replaced every replaceable part over the years, and for the last time was able to get the board to work (1) last time in the "smart-wash" mode which told me the drive components (pumps) were working ok, so I determined the board was bad. The board was ordered on a thursday and delivered on a sunday (fedex), installed same day, took me at least an hour to get door apart and remove the wiring harness (8 of them) without breaking the harness or destroying the wires. Once installed and back together it worked very well. When I placed the order the person on the line emailed me a helpful video link (youtube) on how to get the door apart. Nice job !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Springhill, FL
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
element not working
laid dishwasher on its side and unscrewed element. returned unit upright & replaced element. reversed process and reinstalled unit under cabinet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mitchell from THONOTOSASSA, FL
- Parts Used:
- WPW10195175
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
soup dispenser was broken
went to utube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from DEVINE, TX
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Wrench (Adjustable)
Element was no longer working. Dishes were not drying.
Watched a video and seen how easy it was to repair. Just disconnect the power, water and return drain. two bolts and replace element . The difficult part was removing and replacing the dishwasher...piece of cake.
Was this instruction helpful to you?
Thank you for voting!
The plate was missing at the time we purchased the house.
It was ok but screw holes were not in the right spot but we put one in and that is sufficient for now. It prevent thing from follow under it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eladio from LOGAN, OH
- Parts Used:
- WPW10538166
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Develeoped a leak on the bottom.
Pulled dishwasher out of compartment, removed all parts underneath. removed inner parts, removed pump assembly. Installed new pump assembly and grommet. Reassembled in reverse order, test ran and unit was operating normal and no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Warren from Campbell, CA
- Parts Used:
- W10542314
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
Slight leakage under door
Note that the door gasket only seals the top and sides around the door. I had leakage under the door so I was not sure this gasket would have any effect on the problem. However the old gasket was frayed and needed replacement so I started there.
The repair video was unclear on some fine points that cost me a bit of time at the beginning for trial and error. The information I provide here will save you that time, but watch the video first to get the general idea.
The gasket is longer than the channel it fits into. The video shows starting at the bottom on each side but not what to do with the excess length. For this reason I started at the top: Fold the gasket in half to find the center point then align that with the top center of the channel.
The video refers to an arrow point on the gasket. I found that confusing. There is a flat part that has ridges on both sides: That is the part that slides into the channel. One side has three ridges and the other has two: The side with three ridges faces the wall of the unit and the two ridges face the inside of the dishwasher.
Push gasket into the channel as shown in the video but starting at top center. Check to see if the leftover gasket on each side is close to the same length. If not, remove, recenter, and reinstall.
The bottom of the channel on each side flares out toward the door. This automatically directs the leftover gasket under the door. I was concerned that this would leave a gap and cause a leak but it didn’t.
Run the unit and check for leaks.
The repair video was unclear on some fine points that cost me a bit of time at the beginning for trial and error. The information I provide here will save you that time, but watch the video first to get the general idea.
The gasket is longer than the channel it fits into. The video shows starting at the bottom on each side but not what to do with the excess length. For this reason I started at the top: Fold the gasket in half to find the center point then align that with the top center of the channel.
The video refers to an arrow point on the gasket. I found that confusing. There is a flat part that has ridges on both sides: That is the part that slides into the channel. One side has three ridges and the other has two: The side with three ridges faces the wall of the unit and the two ridges face the inside of the dishwasher.
Push gasket into the channel as shown in the video but starting at top center. Check to see if the leftover gasket on each side is close to the same length. If not, remove, recenter, and reinstall.
The bottom of the channel on each side flares out toward the door. This automatically directs the leftover gasket under the door. I was concerned that this would leave a gap and cause a leak but it didn’t.
Run the unit and check for leaks.
Was this instruction helpful to you?
Thank you for voting!