66513173K702 Kenmore Dishwasher - Instructions

I looked at the position of the remaining Tine Pivot, since there are four on this dishwasher upper rack, and positioned the replacement pivot and pressed it into place. It was a snap (excuse the pun!). NOTE: My dishwasher's Model Number was not in the list provided herein. I had to search a couple of models to find the Upper Rack that looked like ours and to find the Tine Pivot replacement part that looked like ours.That process took longer than the "repair".

First I replaced the lower door seal then I replaced the door gasket. The instructions were clear so both were pretty easy. Unfortunately neither fixed the leak. After further research I discovered that the screws on the pump had become loose. I used a torx driver to tighten the screws. Time will tell, but I am pretty confident that this has fixed the problem.

1) Pull out dishwasher from under counter. 2) Disconnect spring located at the bottom on each side of dishwasher. 3) Using socket remove pulley wheels from each side at bottom. 4) Install new pulleys on each side. 5) Wind pulley cord around both wheels and attach to one end of the spring on each side. 6) Using pliers extend other spring end to lower frame of dishwasher on each side. 7) Open and close dishwasher door to test. 8) Replacement complete

Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

Very easy. I removed the two screws on the base plate, then the two screws that attach the washer to the cabinet, and pulled the washer out of its slot. I installed the broken side and closely checked the other side and felt it didn't need repairing. I put it back together and the door works very well.

Thanks,
Ted K.

It was very easy.

Removed existing gasket by pulling up from the bottom edge. Clean groove where gasket came out of with a tooth brush and then replace gasket starting in the middle near the door latch. Make sure gasket is evenly distributed on both sides.

0) assure main power was off
1) Opened up the panel assembly according to the instructions and the partselect video using the torx driver.
2) snipped the wires from the old part
3) patched in the new part by twisting the wire ends, inserting them into the assembly and tightening the screws.

Had my dishwasher up and running again within 15 minutes.

Pulled up old spray arm and snapped new on in place. Took less than a minute and no tools. Dishwasher is like new again.

lower wash arm cracked by spinning into items hanging out of bottom of basket. part twists and snaps right in. glue did not fix.

Attached new link, then stretched the spring with pliers and routed link over the pulley. Replaced both links.

Kill power to unit. Turn off water supply. Remove front access panel. Remove screw holding valve housing. Remove valve. Disconnect water lines. Replace valve in housing. Reconnect water lines with addition of thread tape. Reinstall valve and housing.

went to utube

Once I figured it out it was not bad at all and most of all it worked, no leaks. I just cleaned some old glue off the stainless steel, dried it well, ran a bead of glue like directions showed, squeezed in the new gasket, closed the door for 24 hours then ran the dishwasher. No Problems.

I went on line and saw a video mentioning it may be the fuse and in order to verify that, take piece of scrap wire and jump pass the fuse.If the lights come on then its the fuse,I did and it was.So I found your web site, typed in the word fuse and the part number came up w/ your video showing how to install it. It was GREAT and what a great idea too having the video available w/ the part! I killed the power and I unscrewed the screws and placed them in the pattern they came out of because some are longer than others. I supported the front cover with my knee and had found the wires in advance so I knew which ones to cut, strip and screw into the new replacement part.I replaced it back in the snap on fuse holder and re-screwed it back together starting with the latch ones, using a criss cross pattern like on a tire. And that was that...I will DEFINITELY use this site again...........hopefully not for a while! Thanks so much.