66515791790 Kenmore Dishwasher - Instructions

Easy fix. It’s a screw on by hand piece.

Removed old rack opened box inserted new rack. So simple sorry I waited so long to replace.

Took out old rack, put in new one. Part arrived on time and was an exact match to the original.

required NO tools,

just unscrew the large thumb screw, and replace the washer arm bearing!

problem solved like that!

maybe a 5 min job. part was a perfect match.

Removed broker washer arm mount with screwdriver and replaced. New parts clipped right on to upper rack, no tools needed. Didn't really need to replace the tube holder but it was brittle so I put it in the order.

The old gasket around the door pulled out easily but was pretty nasty. While cleaning the channel out, kept finding more gunk that had built up. I decided to go ahead and take off the Inner Door. Used Torx driver to take off the screws. Found a tremendous amount of gunk built up. Was well worth taking the extra time to clean it all out. Replaced the Inner Door and put new gasket in channel. No more leaking!

I put the bearing ring on the washer arm and then screwed on the retainer nut.
Easy to order the needed parts

Just removed the old lower dishrack and set in the new one. Nothing to it.

Screwed on a new one. The real story is getting the part. I called about noon one day and the part was dropped off at my house by FedEx the next day. Unbelievable. And the lady I talked to found the part number etc that I needed in a few minutes. Great service at a fair price.

Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

At first, I suspected the door seal was at fault. However, after reading others' repair experiences, I found the dishwasher may leak if the wash arm bearings are worn. So, I took a look at those, and indeed they were quite worn.

After receiving the parts in the mail, I called my 7 and 9 year old kids over. They were excited to open the package, and weren't too disappointed when they found it was dishwasher parts. I told them it was up to them to fix the dishwasher. As I sat on a stool, I instructed them what to do. They did a great job and now it doesn't leak any more.

First I removed the nut holding down the lower washarm in place. I then lifted up the lower washarm where it's held in place by the nut. I replaced the two new parts: The lower sprayarm seal that seats underneath the lower washarm and the washarm bearing ring that seats on the top of the lower washarm just underneath the nut. A schematic parts list diagram can be downloaded on the KitchenAid website. The wobbling motion of the lower washarm still seems to have the same amount of play as it had before I replaced the two parts. The lower washarm itself is in fine shape including the nut. I even attempted several other different ways to install the seal and bearing ring, yet the washarm still wobbles when I manually spin it. I called KitchenAid to find out if wobbling of the lower washarm was normal. Unfortunately, the person I spoke to didn't seem to me to knowledgable enough in this area.

Removed spray bar by removing the plastic finger thumb screw and replace as shown by you web page. Very simple.

used a screw driver, removed 2 screws, removed broken piece, screwed in new part ....all done :)
took less than 15 minutes to do*

i just wanted to let everyone know..I ordered the part on a monday and received it on wednesday I was amazed...the part fit perfectly ...and was very easy to install myself....ty so much ...

I poked the old gasket with a fork tine so I could get a grip on the old gasket as I didn't have pliars, pulled it out in less than 4 seconds, folded the new gasket in half and started center top of the slot the old gasket was in and pushed the new gasket in on each side from the top to the bottom. Very easy. I'd say it took me longer to open the package with my teeth than in doing all of the above.