66515791790 Kenmore Dishwasher - Instructions

I ordered a dishwasher soap dispenser "lid assembly". When it arrived, it was not an assembly at all but only a lid. I had to reorder a pin and spring, When i finally had every thing, it was an easy repair.

I bought the kit because it had other parts that I thought I needed.

The 1/4 inch impeller bolt to shaft would not budge with a nut driver so I had to use a ratchet to loosen it. I could not hold the drain impeller with an adjustable wrench so I had to use a vice-grip. This still did not loosen it so I used an oscillating power saw to cut away at the bottom of the drain impeller being careful to only cut so deep, I didn't want to cut into the motor shaft. Once I had cut some grooves into the drain impeller, I could break it into pieces and remove it. Upon reassembly I tightened the 1/4 inch bolt with the ratchet.

This spinner is attached to a plastic module PN WP3379369 which is held in place by two screws to the top of the dishwasher. I was able to temporarily reattach the spinner by using a hot soldering iron to melt the nylon axle that goes through the spinner. By using a very small metal washer placed on top of the spinner I was able to melt enough off the end of the nylon axle so as to keep the spinner in place and still be able to rotate. By far the most difficult part of this repair is removing the two stops that prevent the upper washer rack being removed from the machine. Doing so requires using a pair of long nosed pliers and taking note of what needs to be squeezed. Even if installing a new part the upper rack needs to be removed in order to get access to this central part.

The nut had broken off even with the top of the threaded area, so we had to remove that broken part. We did so by using small pliers and inserting them in the opening and held them in a spreaded position while turning the broken piece out. We replaced the three new parts and put it back together and it works fine. So easy and much cheaper that having a repairman come in. Took us less than 15 minutes.

Pulled dishwasher out from counter. Took cover off and replaced door springs.

I guess some food got caught in the water level sense float and caused it to mal function.
In the diagnosis process, I removed the arm to clean out any debree in the strainer ( found broken glass). I also found that the two rings mentioned above were worn. I replaced them and all is well.
Thank you for fast response with the replacement parts.

Removed broker washer arm mount with screwdriver and replaced. New parts clipped right on to upper rack, no tools needed. Didn't really need to replace the tube holder but it was brittle so I put it in the order.

Screwed on a new one. The real story is getting the part. I called about noon one day and the part was dropped off at my house by FedEx the next day. Unbelievable. And the lady I talked to found the part number etc that I needed in a few minutes. Great service at a fair price.

Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

Removed old rack opened box inserted new rack. So simple sorry I waited so long to replace.

Took out old rack, put in new one. Part arrived on time and was an exact match to the original.

Researched parts - 10 minutes - - - Ordered parts - 5 minutes - - - Waited for parts - 14 DAYS! - - - Installed parts - 5 minutes

Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!

I went back to the web site to make sure I'd ordered the right part.?? looked at the diagram and then watched your little video.?? He had the part hooked opposite of what was shown. (The arm wouldn't rotate) So I turned it arround. While he was still??. It took me less that 5 min and the dishwasher is working Great.????