66516342301 Kenmore Dishwasher - Instructions

I simply pulled out the old gasket and pushed the new one in with my fingers. I had to trim about an inch off the length with a utility knife. The seal is nice and tight now and we have no more water leakage.

Replaced pump and motor. For the price of the products individually, it only made sense to do the whole thing. As someone else mentioned, much easier to remove the dishwasher and turn it on it's side to remove/replace. Disconnect 3 fittings, 3 stop devices and remove. Other than getting about 20 cuts on my hands from all the metal, it wasn't bad at all.

Was able to replace and repair without taking the dishwasher out. Thermostat is behind and to the left of the power junction box. Has 2 wires going to it. It is up against the bottom of tub. I used an angled mirror to see what I was doing. 1 small screw to detach and pull down thermostat. Be sure power is off before you start. Also reprogrammed defaults. Hit any button 1-2-3, 1-2-3, 1-2-3, fast and close door. Let it sit 15 min to run and re-set defaults. Now I have heat and dry dishes.

I snapped on the new part onto the track. It was that easy! :) Thank goodness the part was available from Part Select!
T. Edwards

Removed leads from fuse and installed jumper wire (while the power was off, then turned back on) to determine that circuit board was still good. Ordered new fuse and installed using existing wire connections. Did not splice in new connectors that came with fuse. Wires were clean and good and did not want to cut and splice.

I had removed this part several times before, it had clogged from sediment, so I had practice. That issue was resolved, but I determined the water level during the wash and rinse cycles was low, and the valve appeared to be the culprit. The trick is to remove the valve from the bracket, removing the single screw, and sliding the unit so the tangs on the bracket can be pushed to the rear and then towards the front. When you disconnect the electrical connection, then the valve can be pulled out towards the front for better access and to disconnect, if your supply hose is long enough. That makes swinging the wrench easier. Other wise it is tedious. Make sure to reapply thread tape after reconnecting the supply hose.

Replace motor/pump assembly

Unscrewed the top of the dishwasher from the counter top and slid the appliance out part way in order to reach the door spring. I loosened he spring from the bracket then slid the sleeve over the bracket. I reattached the spring to the bracket, slid the dishwasher back in and screwed it to the top just like it was prior to removal. Easy as pie.

Bent the plastic housing down holding the spinner. Slipped the top of clip in slot on top of housing. Attached spinner and bottom of clip by holding top clip and pushing bottom of clip in place. No tools were needed.

Pulled everything out the front, and dug down to find a thrashed chopper assembly (like a little garbage disposal). The previous owner just tossed anything in; pop tops, plastic cutlery, etc.
Didn't pay attention to the exact installation of the chopper as I pulled it out, but, it turns out that it only goes in one way.
Used pictures and instructions I found online as a guide and didn't have any issues.
Replaced the check valve because it isn't expensive and I was in the neighborhood.

Remove upper tray and spray arm. Remove two screws retaining pipe for upper spray arm and overhead. Unscrew retainer on top of lower spray arm and remove. Gently rotate the upper feed pipe clockwise until pipe can be removed from lower pipe. You may then remove the lower pipe and bearing housing where the seal is. Reverse order for reassembly. I also replaced upper spray arm bushing. Very simple, remove one screw and the arm will come out.

This procedure assumes that the DW water connection and drain are flexible. Remove Phillips head screws (2) mounting top front of DW to underside of counter. Grasp door and gently coax DW outwards approximately 1 foot. WEAR SAFETY GOGGLES. On RHS check lower end of door spring and note in which notch the spring sits. On RHS, grasp white plastic connector ("hinge bushing", with spring looped around one end), stretch the spring while carefully lifting other end of connector up, out of slot in door hinge lever. Pry door hinge lever 1/8" away from DW body while sliding friction sleeve over its end. Work friction sleeve past hinge hook, past wider section, into narrower slot (about 2" from end of hinge hook). Raise door to closed position. Insert and hold lower (90 degree) end of spring into the same notch that it was originally in (mine was in the 5th from the front). Loop the door end of the spring into one end of the white plastic hinge bushing, then insert the other end of the bushing into the door hinge lever's hook while stretching the spring. It does not require much strength. CAUTION: If the lower end of the spring is not properly inserted and held in the notch, it can pop out and possibly injure you! Repeat for the LHS. Push the DW back in place, and reinstall the two mounting screws.

The replacement of the gasket was simple and required only a flat-head screwdriver to push the rubber into the groove around the opening of the dishwasher. Took only about 15 minutes and the door is a tight fit now. I wish I had replaced the gasket 6 months ago when it first started coming loose when we opened the door to the dishwasher.

I looked up the most common problem with this model and it was the chopper assembly. I removed everything down to this. Sure enough, mine was broken off and the screen was completely clogged with debris. It was not difficult to replace, but it did take me a few minutes to slide it in to place. Ladies, you can do this. No need to call a repairman! Look up the repair manual and see where the assembly is. I had no idea it was even there. My dishes are spotless now.

After pulling the dishwasher out from under the cabinet, I found it underneath near the back right side. I disconnected the old thermostat, unscrewed the clamp holding it into place, put the new thermostat in, screwed it back in and replaced the two plugs. Then I pushed the dishwasher back into place, and it initially didn't work until I found an online forum that was able to identify the reset command for my dishwasher (for the WDT710PAYM4, press any three buttons in a sequence of 1 2 3 1 2 3 1 2 3. After completing that all the lights lit up, and I shut the door leaving it for half an hour) Once the reset finished, the heated dry worked like it was suppose to.