58717245990 Kenmore Dishwasher - Instructions

Removed the screws that hold the panel on ( just the top ones-no need to go all the way down the sides. Need a "star" headed screwdriver to remove the switch itself. Then removed the wires (4),one be one, so as not to mix them up. reinstalled all thescres for the switch, then the panel. Job done.
What amazes me is that Frigidaire doesn't read your page to realize that the handle assembly was defective and send out a recall. look at all the repars listed in your site , and these re just from the people that have responded with comments and who use your service. New handle/switch is much more sturdy with a higher density plastic that the original. Your service is easy to use, prompt and accurate. Fixed the dishwasher while my wife went to the store. Dishwasher done in 15 minutes and watched theNCCA tournament for 2hours in complete peace !!!!! No need to tell the wife only spent 15 minutes.

First i removed the screws on the back panel, unscrewed the latch, removed the wires and installed the new latch.
I found the latch is too expensive for a little plastic part.

Just pulled the old gasket out and popped in the new. I did trim it too shrt however so be careful not to do that.

shut off the power on the breaker box, 6 screws inside the door on the tolp and side,pulled 4 wires off, 2 star head screws on the unit. took bad unit off,put new one on and put the screws back in.

5 minutes

After watching the repair video, it was 'easy as pie'. I would have thought the gasket was too long and cut it off if not for the video. Thank you. Saved a great deal of money not having to have a repair person do the work. I strongly recommend watching the video.

Removed the screws holding the door panel and as the sheet said was the way the it went. Two screws holding the handle latch and replaced it and put the door back on. There was 4 wires to replace on the latch. Replaced the gasket and the job was done. All in all it was a very good experience with good instructions and very good same day shipping. A VERY GOOD EXPERIENCE.

Removed the front cover by unscrewing the 8 screws. Removed the latch and attached new one. Re-attached front cover, and it works fine.
The gasket was in fine shape, and I question why I had to purchase the gasket in order to get the latch. Seems crazy and an unecessary expense on my part.

removed screws to loosen front door panel then removed the wire connection, then removed the broken latch with screwdriver, installed new latch in same manner, fastened front panel back with the removed screws and I was back in business, easy as pie.

removed screws holding door panel, turned off electricity,removed old part and installed new dispenser, the dishwasher is back in business. Be sure to use the proper screws when putting back the door panel.The instructions for installation were in the new part assembly.

Thank You for all your help

Pat Johnson

Take front off about 12 screws two screws held latch on took four wires off two white two black very simple to replace.

It was a walk in the park. Unscrew the six screws in the back of the panel to reach the latch. Unscrew the two torx screws in the front of the latch and replace each of the cables, one by one, in the new latch in the same order. Put the screws back into place in reverse order and... voila, wthout a single shock !!

First I removed the control panel and then removed the screw holding the handle. I then pulled the connector wires off and onto the new handle. I then screwed the new panel into place. Easy job, no mess.

Just pushed it onto the rod that held the old one

1.Turn off electricity. 2. Remove two Phillips screws on either side of front panel 3. Remove front panel 4. Remove 6 screws from the old dispenser 5. Pull both wires connectors from dispenser 6. Remove dispenser 7. Install the new dispenser and reverse the steps

Followed the YouTube video. Replacement fit perfectly , only took 10 minutes to replace.