58717245990 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Seth from Seattle, WA
- Parts Used:
- 154219201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Dishwasher was leaking water
The spray arm had become damaged on one side -- one side had apparently melted off. I replaced it, and it seems to have fixed the problem for now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pam from Cherokee, AL
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing a wheel on dish rack
just slid the wheel on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Prior Lake, MN
- Parts Used:
- 154219201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Lower repair arm failed and did not allow dishwasher to complete wash cycle. Repair completed in less than 10 minutes and dishwasher is now functional. Thanks.
remove center nut retaining the arm to the unit and replaced the arm.
replaced the nut.
complete.
replaced the nut.
complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from canonsburg, PA
- Parts Used:
- 154637401
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
The water inlet valve cracked and fell off-again!
FIrst I had to turn off the water supply, remove the bad part and cap off the copper water line.
I found the correct part on line and ordered it. When the part came, I uncapped the water line, doped the ends and refit the valve. Turned the water on an voila!. I actually did it! I was pretty proud of myself. It only cost me the price of the part and not a plumbers fees as well.
I found the correct part on line and ordered it. When the part came, I uncapped the water line, doped the ends and refit the valve. Turned the water on an voila!. I actually did it! I was pretty proud of myself. It only cost me the price of the part and not a plumbers fees as well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Mastic Beach, NY
- Parts Used:
- 154637401
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Intake valve was leaking
removed two screws the disconnected the two hoses (after shutting the water off of course). It was easy.
Unfortunatley the water warped the wood under the vinyl flooring which is new and I really love. I would suggest that a rubber or some type of water proof material be placed under the dishwasher so that if it leaks it won't get at the subflooring. If this had been the case I would have noticed the leak right away.
Unfortunatley the water warped the wood under the vinyl flooring which is new and I really love. I would suggest that a rubber or some type of water proof material be placed under the dishwasher so that if it leaks it won't get at the subflooring. If this had been the case I would have noticed the leak right away.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Giovanni from Glen Burnie, MD
- Parts Used:
- 5304442175
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door Latch Broke Off, Can't Close Door
Very easy to remove old broken door latch assembly, easier to install replacement. With door fully opened, I removed the 8 screws holding down the whole front casing, including the controls casing. Removed 2 Torx screws holding door latch assembly and then made sure that I marked all 4 wires before disconnecting them from door latch assembly. Connected wires to new door latch assembly, secured it with the 2 Torx screws, aligned and secured the controls and front cover casings with 8 screws. Done within 30 mins. Thanks guys for posting how-tos and thanks to PartSelect for a very fast shipping!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from lees summit, MO
- Parts Used:
- 5304507405, 5303943103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
no issues
replacing 2 wheels was a breeze. did not need the screws afterall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Casa Grande, AZ
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
latch broke unable to open door
Take front off about 12 screws two screws held latch on took four wires off two white two black very simple to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- erika from deerfield beach, FL
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
latch broke had to open door with a screwdriver
removed screws to loosen front door panel then removed the wire connection, then removed the broken latch with screwdriver, installed new latch in same manner, fastened front panel back with the removed screws and I was back in business, easy as pie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Amherst, NY
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Latch broke and dishwasher could not be opened.
Removed the front cover by unscrewing the 8 screws. Removed the latch and attached new one. Re-attached front cover, and it works fine.
The gasket was in fine shape, and I question why I had to purchase the gasket in order to get the latch. Seems crazy and an unecessary expense on my part.
The gasket was in fine shape, and I question why I had to purchase the gasket in order to get the latch. Seems crazy and an unecessary expense on my part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Whitman, MA
- Parts Used:
- 154574401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
detergent door/dispenser would not close,
removed screws holding door panel, turned off electricity,removed old part and installed new dispenser, the dishwasher is back in business. Be sure to use the proper screws when putting back the door panel.The instructions for installation were in the new part assembly.
Thank You for all your help
Pat Johnson
Thank You for all your help
Pat Johnson
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Houston, TX
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Door latch broke
First I removed the control panel and then removed the screw holding the handle. I then pulled the connector wires off and onto the new handle. I then screwed the new panel into place. Easy job, no mess.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Manuel Guillermo from Miami, FL
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door handle came loose due to broken latch
It was a walk in the park. Unscrew the six screws in the back of the panel to reach the latch. Unscrew the two torx screws in the front of the latch and replace each of the cables, one by one, in the new latch in the same order. Put the screws back into place in reverse order and... voila, wthout a single shock !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from STEWARTSVILLE, NJ
- Parts Used:
- 5304532229
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing part
Just pushed it onto the rod that held the old one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerald from MILFORD, MA
- Parts Used:
- 154574401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door broken would not close
1.Turn off electricity. 2. Remove two Phillips screws on either side of front panel 3. Remove front panel 4. Remove 6 screws from the old dispenser 5. Pull both wires connectors from dispenser 6. Remove dispenser 7. Install the new dispenser and reverse the steps
Was this instruction helpful to you?
Thank you for voting!