66515974991 Kenmore Dishwasher - Instructions

I removed the old wheel assemblies
(4 total holding 2 wheels each) with a slight prying with a screwdriver to
ease it off the rack. After the first one, the rest were a little easier.
The new ones had to "mate" a certain way and then just needed a push of the hand.

My husband replaced the entire soap dispenser until in under 30 minutes. I stayed out of the room. :) I didn't hear any swearing, so I assume it went fairly well. Sorry that I can't give you detailed instructions. He didn't need a manual or any type of directions. I guess it was kind of obvious how to do it. Just be sure you turn off the power first.

I ordered the upper and lower rack replacements PLUS additional wheels and other attachments because I could not tell from the schematic on the website whether or not the smaller pieces came with the rack.

As it turned out, the racks came ready to install and all it took was a limber nephew to take out the old ones and put in the new. Now I have plenty of spare parts in my own inventory in case the wheels, etc. need replacing.

I feel guilty sending you this repair story because all I did was order the parts on your website and then conned my nephew into making the exchange.

The parts arrived very quickly and in good condition. In fact, the new racks are an improvement over the ones that came with the dishwasher originally. Ms. Susan McNutt was quite helpful in keeping me informed of the status of the part that was back-ordered. It was a pleasure dealing with PartSelect.com.

compared it to old rack. Parts snapped together in 5 minutes. the fit was good. Kit did not include the silverware baskets, or the fold down narrow shelf.

Great fit. take out old one and drop in new one. Piece of Cake.

At first I thought I needed a new bottom rack for my dishwasher. Out of curiosity, I watched the installation video and realized that the Tine Row installed separately and that was the only part I needed. I am appreciative of being able to access that video and the money I saved. Installation took seconds to complete.

1 Screw 5 minutes thanks for the quick service will definitely use ya'll next time

No Water supply to Dishwasher. Turned off main Supply valve under sink.First took off old Diswasher supply valve and repaired it by cleaning it and it worked for two weeks. I ordered the part, but then cancelled it and Partselect service was great and cancelled it immediately. After it went down after 2 weeks I re-ordered it and it came in 4 days.
To Take this part off I removed mounting scews with nut driver, disconeected electronic plug connector, removed the compression fitting from the water supply and removed the outlet hose..reversed all of the above to install.

Bent back metal ears over door hinge pins, released door springs from door hinges. Lifted door off of hinges and replaced corner drain back seals and lower door seal.Still leaks so obviously I have another issue or the door seal is lousy quality. I've completed this project before and never had another issue for 6 years.

Old style tube was an assembly of 3 separate parts, so it could come apart to pass through the holder bracket easily. New style tube was a single piece. The moldings on either end are too large to slip through the holder bracket circular ring. Apparently, the newer style holder brackets have a slit or break in the ring. Not so with the older bracket I had. I merely cut my own slit at the top of the ring on my old bracket, allowing me to spread the ring wide enough to allow either end of the single-piece tube to pass through. There is very little pressure on the holder bracket ring - it's just a holster for the tube. So the slit does not affect performance. Job done in 30 min.

The part arrived much sooner than i was ready for. with a square allen wrench I was able to install the tube in no time.

Removed the washer from the cabinet, although the repair kit could have been replaced without this step. However, it still made it easier. Removed the spray arm assembly and the top cover to the motor. I had to block the motor to keep it from turning while I unscrewed part number 11. The rest was very self explanatory. The "impeller" was seized onto the motor shaft (20 years old) so I had to use a chisel to break what remained off, then clean some corrosion from the shaft. The repair kit worked and the pictorial parts diagram that came with the kit was very clear. Bottom line: "Easy peasy, lemon squeezy!" Great web site for diagnosis and parts diagrams!

The repair was simple except for removing the thread portion of the old retainer nut from the lower housing. I had to remove the lower housing and separate the male threads of the old plastic nut from the female threads in the lower housing. That took 25 minutes since I did not want to ruin the female threads. Once removed, the new parts went into place easily.

I removed the door gasket first by sliding it out.Then I pulled the door seal out. It suggested removing the springs,very hard to find and do, so we left them in place and did not use two parts of the kit because they were still good.
Putting in the door seal was a bit tricky because we had to use something to push it into the groove.That was the reason for the credit card. It was easier to push it into groove rather than doing it with a screw drive for fear of punacturing a hole in the rubber gasket. It worked well. Then we kept checking to see if the door shut properly, It was tight at first, but seemed a little better after adjusting the seal a bit.No leaks after that.

The repair went well with the major problem being I replaced the drain hose without removing the dishwasher from it's position. Due to this I removed the drain end with out being able to see the hose and put it back on by feel. Over all I was back up and running with in 30 minutes and everything has worked very well so far.