6651591680 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Nicole from Newnan, GA
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The previous rod holding the cup in place broke
Remove completely the old one and installed the new entire kit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- craig from Columbia, TN
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
was just missing the door and spring
You slide the pin that holds the door in the first hole. then you slide the spring in next. The you slide the pin through the last hole. After that you gently push the door onto the pin till it snaps into place. And your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karolyn from Wellington, FL
- Parts Used:
- WP304170
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Super Fast Shipping
The part arrived the next day with regular postage, outstanding service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Ritzville, WA
- Parts Used:
- WP302711
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
leaking badly & not cleaning dishes
You need a properly sized hex (Allen) wrench to get the screws out. Basically simple: remover bottom roller tray, unscrew large plastic holding bolt, remove lower spray arm, unscrew bolts (be sure the wrench is sized right or you might strip the heads), and replace gasket; then reverse procedure. Chances are if the gasket was bad, it will be very obvious (out of circular slot and stretched).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Sebring, FL
- Parts Used:
- 4387043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Detergent door would not spring open-spring was broke
Put on new door, making sure the spring was set to flip the detergent door open in order for the detergent to properly do the dishes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Tucson, AZ
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wheels on Rack Needed to be Replaced
A VERY easy repair! I simply pried off the old wheel assemblies with a screw driver and popped on the new ones. I was a little concerned about the new ones fitting correctly as the dishwasher is over 25 years old, but after a week they still work fine. An easy fix to an annoying problem....wish I had ordered these ages ago! Bottom rack of my dishwasher now rolls in and out like new (instead of the the few remaining wheels constantly falling off!) Very happy I ordered these and delivery was quick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delano from Durham, NC
- Parts Used:
- 4387043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
spring on dispenser broken
Removed cover and broken spring ,installed new spring and cover.Did it all in less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Powell, OH
- Parts Used:
- 675238
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Dishwasher wouldn't drain
Turn off the breaker to the dishwasher - there will be water very near the motor and other electrical components. I first scooped and towelled all the water out of the bottom of the dishwasher. The drain valve can be accessed from the bottom front of the dishwasher without pulling the unit out from under the counter. There were 4 screws to remove the 2 bottom metal panels. Next use pliers to loosen and slide back the hose clamp connected to the drain. Have a towel ready and pull the drain hose off the white check valve. The check valve can then be removed by unscrewing it - you may need to use pliers. Put the new one on and everything back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Del Mar, CA
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the rollers were completly broken off & I had to lift the bottom tray in/out of the dishwasher
popped off the old rollers + tracks; then snapped on the new ones; as my granddaughter would say "easy peasy lemon squeezy". Took hardly any time at all. :-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aubrey from Fouke, AR
- Parts Used:
- 675611
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken door springs
I ordered the parts on Fri. and they came on Sat. Thanks. I had to pull the dishwasher forward about 6". Then just put the springs on. They don't have much tension with the door closed. Easy. Thanks again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Columbia, MD
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Soap cup latch was broken and dispenser cover was worn.
Replacing the cup latch and dispenser cover was pretty easy. First, I removed the inside cover of the door of the dishwasher. Then I carefully removed the plastic covers/slides on the door, removed the broken cup latch and then inserted the new one. Replaced the plastic covers/slides, the reinstalled the inside cover on the dishwasher. Next, I removed the dispenser cover and installed the new one. It snaps off/on, by the way. It only looks like it slides on/off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Millbrae, CA
- Parts Used:
- WP302711
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water leaking from the right front of appliance
The repair was simplicity itself. Remover the sprayer arm, removed the torx screws, replaced the seal, and reversed the process of disassembly. When I found out where the dishwasher was leaking from, I called KitchedAid and was ready to replace the overflow float. The part was 42.00 and wouldn't have fixed the problem. When I found this web site and read other peoples experience, I checked the pump seal, and it was obvious that it had blown out. That saved me a Loy of time and money.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- trevor from esko, MN
- Parts Used:
- 675806
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
rattle in the dishwasher, not working
My husband took the dishwasher apart three times, it was a little frustrating, but was worth the $50 part because it made his wife, very, very happy! A dishwasher operating is on the top 5 list of favorite electronic items in our house.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joel from jena, LA
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rollers had broken on old rack
Received new rollers promptly as ordered. Removed the old ones by snapping them off and simply snapped the new ones on. Took less than 5 minutes and job was a complete success. Wife happy and I am safe for now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from mastic, NY
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lower rack wheels
took off the old wheels and put on the new.couldn't be easier.
Was this instruction helpful to you?
Thank you for voting!