6651544591 Kenmore Dishwasher - Instructions

Safety First: 1) I shut power off to dishwasher, 2) Shut water off to dishwasher, 3) Checked electrical with tic tracer to confirm power was off after removing bottom dishwasher panel, 4) I checked the orientation of old valve: connection plate, water inlet tubing, hose connection, and electrical connection. Then I removed the 2-screws that held the valve in place with a nut driver. Next I removed the compression clamp from the rubber hose with pliers and a screw driver. Then I removed the compression fitting and copper tubing from the old valve. Note: Kenmore used a compression fitting to connect the copper tubing to the original water valve. That said, I had to remove the old fitting and install a new one (using a pipe cutter on the copper tubing before installing a new compression fitting). I also bought a new valve elbow because the old one was not serviceable. With all three connections made up (the rubber tubing connected to the new valve along with the electrical connection, and the new elbow and compression fitting installed) I tested for leaks and reconnected the holding bracket to the side of the dishwasher frame. Before calling it good I vacuumed out the area under the dishwasher. Note: because the water inlet valve is located close to the floor, all the work had to be done while laying on the floor...awkward. This too, I had to purchase a new valve elbow and compression fitting so halfway through the project I had to make a run to the hardware store. Overall, replacing the water inlet valve on a 10 year old Kenmore dishwasher is an easy project...pretty straight forward but having to go to the hardware store stretched the installation time out to over an hour.

Turned off power to dishwasher. Removed inner door panel. Cut wires as directed and installed new switches. Also installed new spring on soap door opener. Reassembled, ran and tested. Take your time, this repair is pretty simple.

My soap dispenser latch was coated in grit, the gasket was deteriorated, and the spring was barely strong enough to open the door, so the door didn't always latch closed or open when it should. I followed the video and everything went exactly as shown. Once the liner was removed, I discovered the back (including the latch mechanism) was covered in soap residue and other gunk. I hosed it off on the backyard and resumed the repair. The dispenser now latches easily and opens with a convincing SNAP. I wouldn't have known how to replace the latch without the video. Great website!

I replaced the seal, still leaked. Once I noticed that it was only leaking from the left side, we did a Google search to find that the screen in the upper left of the door could be the issue, causing back pressure. Once the screen was cleaned, no more leaks.

Remove lower rack in dishwasher, remove dishwasher, lay dishwasher on it's back, remove and replace motor and pump.Install new impellar with new seal. reconnect water, electrical and drain hose. Easy Peasy

Replacing the cup latch and dispenser cover was pretty easy. First, I removed the inside cover of the door of the dishwasher. Then I carefully removed the plastic covers/slides on the door, removed the broken cup latch and then inserted the new one. Replaced the plastic covers/slides, the reinstalled the inside cover on the dishwasher. Next, I removed the dispenser cover and installed the new one. It snaps off/on, by the way. It only looks like it slides on/off.

Started down Parts Select list of possibilities. Replaced the door gasket (1/2 hour), still leaked. Replaced water deflectors (15 min), still leaked. Was looking at steam vent and read the repair submitted by "mary from Fountain Green UT". Removed and thoroughly cleaned the steam vent (1/2 hour). Stopped leaking and is working fine now. Repairs were very easy using Parts Select instructions.

Took inside door panel off. replaced spring that opens soap dispenser lid during cycle. Put inside panel back on. Works fine now.

I watched the video that you had on line and the repair was done in a snap. The shipping was fast also.

we followed your instructions submitted via e-mail and they worked out just fine....thank you

I installed the opener spring in the direction it was needed to open the door then installed the pin. I placed the door in the position it goes and took a pair of pliers and squeezed the pin into the pin slot. the spring has to be forced into a tension position. I did this by sliding the spring to one side and forcing it into position, the other side is done the same way. works great

Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install

The top of the latch was broken on I had to push the plunger back through the mounting to get it out. ai had to pull the whole assembly apart to get the locking nut out. i remove the latch assy and took about 10 minutes to figure out how to put it back together. Changing it with the help of the video wasn't hard but confusing at times. Thanks for the video.

Followed vidio instructionson web site. Quick easy fix

took out old door gasket replaced it with new, also cleaned the air vent at top of door. Ordered shield at same time but didn't use it, so returned it, haven't received refund yet, but expect one soon. Dishwasher works great and NO leaks. Wonderful website