6651595840 Kenmore Dishwasher - Instructions

Replaced the lower seal, drain impeller,chopper blade, and wash impeller. Problem is still not solved but the inner parts have been replaced. Only thing logical next is the check valve. Unit cycles well and if I turn the dial to just before the rinse cycle and watch, I do see water draining from the unit...Of course while replacing these parts, I checked other things and found a loose spring behind the front cover. It can be seen on the diagram as it is part of the detergent door mechanism (or so I believe), but it is not clear on where the spring actually connects to.

I tried going online to get some diagnostic help and never found a site that had a step by step help plan. I then did a little reading on different sites, to eliminate and perhaps diagnose my problem I use epoxy to glue the impeller(which spun freely) to the screw and it held long enough for me to see how it worked. I surfed sites to find the least expensive drain and wash impeller kit. One site had a cheaper price but I chose Parts Select because of the shipping so the end result was the best results for me. I am not sure but the estimated time was 1.7 or 1.8 days delivery that I did not believe would happen. When I received the parts and did the repair my final time from ordering was less than a day and a half. I could not have done the job myself without the video because the parts were very different. My biggest obstacle, other than my ignorance, was some sort of chemical on the screw that would not allow me to loosen it. I used a dremel to cut the head off and then a torch to heat the stub so I could remove it. After I received the kit I saw a chemical on the screw threads so online research told me heat loosens the chemical. My dishwasher is around 25 years old,I have worked on it three times now and replacing the impeller was the most difficult task to date. Should it last and develop another problem I will go to parts select first and start my quest.

My dishwasher quit working the week before Thanksgiving, and to say the least, my wife was quite concerned. I did not know what was wrong, until I found the info on this website, including a how to repair video. I watched the repair video on the website when I ordered the parts. Other than my wash arm being different from what was shown in the video, it went exactly as shown in the video. I'm glad that the video, and the bag with the parts told me that there are fewer parts than originally were installed on the original. The parts looked like they had been redesigned a little, and were easier to assemble. Overall, I will be getting any repair parts I need for other appliance repairs in the future from here. Thank you for making this experience as easy as it was.

I watched the video then followed the procedure accessing the impeller/grinder from inside the tub. Had I not watched it, I would have torn into it from the bottom by removing the motor, etc. with disastrous results. I was quite depressed when installation of the impeller kit did not resolve the problem. I remembered from the survey that 56% of problems were solved with this kit; BUT, another 24% found that the check valve on the discharge line was the problem. So I removed it and lo and behold, it was partially plugged with broken pieces from the old impeller. The 1 page sheet that comes with the kit is simply a diagram of the parts included, there are no instructions ---- watch the video!!! All said and done, my experience with PartSelect was first class. They are 5 Stars in every category and I would highly recommend them.

followed the basic instructions / diagram supplied, however the impeller was fused to the shaft. Used high speed cutter to remove old impeller and sandpaper to clean up shaft.

I installed the opener spring in the direction it was needed to open the door then installed the pin. I placed the door in the position it goes and took a pair of pliers and squeezed the pin into the pin slot. the spring has to be forced into a tension position. I did this by sliding the spring to one side and forcing it into position, the other side is done the same way. works great

I reviewed your video and followed the steps, I appreciate the video. I used the tools described in the video; it was a simple process. Thank you Parts Select. .

I looked in the bottom of the dishwasher after browsing the website regarding possible solutions. When I removed the bottom spray arm I noticed three screws missing from the pump housing. The loose pump outlet had allowed the seal to push out. Ordered-Normal shipping on the part.

1. Turn off the electrical switch that powers the dishwasher. 2. Open the door of the dishwasher and find the two phillips head screws that secure the top of the dishwasher to the kitchen counter. 3. Remove the screws. 4. Gently move the machine side-by-side a bit while pulling it out onto the kitchen tile (be careful, the water-supply hose, electric cord, and dishwasher drain hose may not be long enough to allow you to pull it out very far - don't break or kink the hoses). 5. Remove (pull off) the black plastic fastener located on the bottom/rear of each side of the dishwasher. 6. Remove the old surround. 7. Lay the new wrap in place and secure with the two plastic fasteners. 8. Push back into place, secure the two screws, check your hoses.

Unsnapped the old rollers and snapped in the new ones. Worked great and easy. I was very pleased that the parts came so soon as well. Thank You, Ms. Cason

Used the diagram and disassembled and reassembled.Used most parts that were in kit as it also fit other models and did not need all the parts.

Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install

My husband took the dishwasher apart three times, it was a little frustrating, but was worth the $50 part because it made his wife, very, very happy! A dishwasher operating is on the top 5 list of favorite electronic items in our house.

Watched "Steve" install the drain and wash impeller kit and then I did it.

My model was DU7600XS0. I disassembled according to the video and the parts diagram here. I found a piece of metal, a pebble, and a wrecked drain impeller. I cleaned out all the debris and began reassembly. I found that the chopper blade shipped with this kit has a lip and will not fit over the metal drain impeller sleeve on this model. It needs to, or else it will not screw together properly and the impeller will not be able to turn. My old one was undamaged, so I used that instead. Also, the large black wash impeller has a shaft that is longer than the original part and because of that, it would not screw on. Again, the original wash impeller was fine, so I used the old one. I replace the gaskets and screwed everything else back together. It works great now. No water is left after the cycle anymore and the sound it makes is back to normal. Money well spent on this kit!