6651595840 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Katherine from Coos Bay, OR
- Parts Used:
- W10311986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
We needed a new bottom dishrack the old one was very rusty
I ordered a new rack, snapped the stuff together, and slid the old one out and the new one in. Fit beautifully. Piece of cake and much cheaper than a new dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Oakland, CA
- Parts Used:
- 4317933
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Three rollers fell off
I removed the old rollers. This took a while to figure out how to get the old rollers off. Also it was difficult due to the fact that they had been on the basket for a long time. As soon as I figured out how to take them off and put the new ones on, it was fairly easy. The instructions were non -existent which is why it took a while.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Erving, MA
- Parts Used:
- 674744
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Door comes down to fast, Broken Door Assist Spring
Turn off power at breaker
Turn off water supply
Remove 2 screws at baseboard plate
Remove 2 mounting screws attaching machine to floor
Open door, remove 2 mounting screws attaching machine to bottom of counter
Disconnected water line
Carefully pulled machine out about 8 inches to expose broken spring
Attached new spring using directions included with package from PartSelect
Reassembled in reverse order
Check for water leak before attaching baseboard plate
Turn off water supply
Remove 2 screws at baseboard plate
Remove 2 mounting screws attaching machine to floor
Open door, remove 2 mounting screws attaching machine to bottom of counter
Disconnected water line
Carefully pulled machine out about 8 inches to expose broken spring
Attached new spring using directions included with package from PartSelect
Reassembled in reverse order
Check for water leak before attaching baseboard plate
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip D from Auburn, AL
- Parts Used:
- 4387043
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Latch had broken on detergent dispenser cover
Remove retainer that holds door color slide in front of door & then remove the slide. Remove cardboard backing, remove electric latch release, remove latch & replace with new one. Open door & slide out the cup dispenser cover pin & spring & replace with new ones. This was all straight-forward & simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Wappingers Falls, NY
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
6 wheels missing
easy - removed old wheel holders & pushed new
ones in place. parts came in two days !!!!
ones in place. parts came in two days !!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Greene, ME
- Parts Used:
- W10311986
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Installed wheel assemblies to rack
Assemblies snap on, no tools needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Las Vegas, NY
- Parts Used:
- 4387043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
soap door hinge broke
I took the pin and i slide it through the first hole attached the spring then sldie it through the second hole and snap the cover on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicole from Newnan, GA
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The previous rod holding the cup in place broke
Remove completely the old one and installed the new entire kit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- craig from Columbia, TN
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
was just missing the door and spring
You slide the pin that holds the door in the first hole. then you slide the spring in next. The you slide the pin through the last hole. After that you gently push the door onto the pin till it snaps into place. And your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karolyn from Wellington, FL
- Parts Used:
- WP304170
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Super Fast Shipping
The part arrived the next day with regular postage, outstanding service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Sebring, FL
- Parts Used:
- 4387043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Detergent door would not spring open-spring was broke
Put on new door, making sure the spring was set to flip the detergent door open in order for the detergent to properly do the dishes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leo from Idyllwild, CA
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Several of the wheels for the lower rack had fallen off.
I removed the rack and then pushed down on the old rollers to remove them from the rack. I then installed the new rollers in the same location.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARVIN from NESBIT, MS
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lower rack wheels broke off roller assembly
Old tandem rack for rollers popped off lower rack by applying a small amount of pressure. New tandem rack rollers look slightly different, but pop right in place. By replacing all four tandem rack rollers the lower rack glides smoothly in and out of the dishwasher. Entire replacement can be done without tools, by hand in less than fifteen minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Millbrae, CA
- Parts Used:
- WP302711
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water leaking from the right front of appliance
The repair was simplicity itself. Remover the sprayer arm, removed the torx screws, replaced the seal, and reversed the process of disassembly. When I found out where the dishwasher was leaking from, I called KitchedAid and was ready to replace the overflow float. The part was 42.00 and wouldn't have fixed the problem. When I found this web site and read other peoples experience, I checked the pump seal, and it was obvious that it had blown out. That saved me a Loy of time and money.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Ritzville, WA
- Parts Used:
- WP302711
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
leaking badly & not cleaning dishes
You need a properly sized hex (Allen) wrench to get the screws out. Basically simple: remover bottom roller tray, unscrew large plastic holding bolt, remove lower spray arm, unscrew bolts (be sure the wrench is sized right or you might strip the heads), and replace gasket; then reverse procedure. Chances are if the gasket was bad, it will be very obvious (out of circular slot and stretched).
Was this instruction helpful to you?
Thank you for voting!