66515892100 Kenmore Dishwasher - Instructions

Looked at other side of top rack which still had the stop. Just had to orient the direction of the stop and push it firmly onto the rack arm. Took a couple tries, but it went in and locked. Works perfectly. Inexpensive and easy fix to to very annoying problem.

After pulling the dishwasher out from under the cabinet, I found it underneath near the back right side. I disconnected the old thermostat, unscrewed the clamp holding it into place, put the new thermostat in, screwed it back in and replaced the two plugs. Then I pushed the dishwasher back into place, and it initially didn't work until I found an online forum that was able to identify the reset command for my dishwasher (for the WDT710PAYM4, press any three buttons in a sequence of 1 2 3 1 2 3 1 2 3. After completing that all the lights lit up, and I shut the door leaving it for half an hour) Once the reset finished, the heated dry worked like it was suppose to.

A Mouse friend had seen fit to chew through the original drain line. I used my Model Number, and was able to order the correct part . It arrived the next day. The job itself is fairly straight forward. You will need to access the rear of the machine. This may include shutting off, and disconnecting the water supply line. (Adjustable wrench). Mine is under the sink, on the "Hot" side. You may also need to un-plug the unit. (recommended) . A pair of (Pliers) will be needed for the spring clamp.

Found the gasket to be wearing out. Once I got the part I took everything apart inside to find that I could have just taken the dishwasher out and replaced from the bottom. It was not difficult, but I've installed a ton of dishwashers. For the average homeowner, this is can be a difficult job since it requires plumbing and electrical skills.

I unscrewed the dishwasher from the counter (two screws under the countertop), and pulled it out about a foot so I could access the friction sleeve. I used a needle nosed pliers to slip a spring latch off the door. Then I slipped the new friction sleeve on and reattached the spring. Tested the door. Success! Super easy. About 5 minutes of work.

The old tine row came out easily and the new one was easy to pop into place. I was pleased that it was so easy to order a replacement part.

Pulled front panel and replaced door switch. Extremely easy but did not fix the problem.

The part snaps on using two plastic retainers (included). You have to pull down gently on the feed tube at the top of the dishwasher to set the top retainer. After that it's a piece of cake.

Our Kitchenaid dishwasher was leaking so I called a repair service. I gave the model number and serial number over the phone and explained the problem. I was told the rubber gasket would need to be replaced. When the repairman came 5 days later he told me that the gasket needed to be replaced but he didn't have a new one on his truck. He ordered one and said he would be back in a week to repair the dishwasher. That took 10 minutes at the most. He then gave me a bill for $200.49 ($71.49 for the part and $129 for the labor)that I had to pay right then. I wrote him a check so he would leave and immediately called the repair company to tell them the price was outrageous and that I had never before paid for a repair before the work was done. I was simply told it was their policy. I then told them I was stopping payment on the check - which I did. I checked on-line for the part and found your web-site and the the part I needed for $27.62. I ordered it on a Monday, it arrived on Tuesday and my husband easily installed it that evening. Thank you, thank you, thank you!

Removed required hardware and dishwasher from undercounter mount. Turned dishwasher on its front and removed the old motor. Installed the new motor and tested for function. Installed once test was successful.

I took the unit apart to find out what was making the loud noise and found the seal on the main pump had been leaking ito the bearing on the motor.

Removed the old tines by pushing out the clips on the end and then installed the new tines and applied clips - took 10 minutes worked slick and the washer basket looks to be brand.

Removed old part and replaced with new part

After researching the issue, it pointed to either a clogged hose or a bad pump. I cleaning the hose, verifying that there was no clog by using baking soda, vinegar and water. It would work, once maybe twice, then the water would sit again. I checked the line again, no issues. I purchased a new pump. The installation of the pump was easy, only to discover that this did NOT solve my problem. I am now considering a new dishwasher or purchasing a new $150 motor. It sucks not being able to send the parts back.

Removed the bottom plate/cover. Unscrew top from bracket. Lucky,had just enough room to pull washer out. Only 6 in. Sleeve had broken off. Needle nose plyers to unhook spring. Slide sleeve over hinge. Hard Part///. Pull spring back into place. with door shut. good luck.