66515933000 Kenmore Dishwasher - Instructions

This kit comes with the link cords and the balance wheels. I only needed the cords. I undid the set screws under the counter edge and slid the Dishwasher out from under the counter. One of the links had a broken cord and the spring had snapped to the very back of the space and was a bit hard to find. I used the good side as a guide to see how to thread the cord correctly. I did not replace the wheels since they appeared to be in good shape and looked like they might be a bit more difficult to replace than just the cord. For a second I thought I had ordered the wrong part because the new cord's attachment point at the hinge did not look exactly like the originals but the new design worked just like the original. I did need one other person to help stretch the spring and hold the door in the best position so I could attach the cord to the hinge. It's working perfectly now and I saved the wheels in case I need them later.

Removed leads from fuse and installed jumper wire (while the power was off, then turned back on) to determine that circuit board was still good. Ordered new fuse and installed using existing wire connections. Did not splice in new connectors that came with fuse. Wires were clean and good and did not want to cut and splice.

I had removed this part several times before, it had clogged from sediment, so I had practice. That issue was resolved, but I determined the water level during the wash and rinse cycles was low, and the valve appeared to be the culprit. The trick is to remove the valve from the bracket, removing the single screw, and sliding the unit so the tangs on the bracket can be pushed to the rear and then towards the front. When you disconnect the electrical connection, then the valve can be pulled out towards the front for better access and to disconnect, if your supply hose is long enough. That makes swinging the wrench easier. Other wise it is tedious. Make sure to reapply thread tape after reconnecting the supply hose.

Replace motor/pump assembly

Bent the plastic housing down holding the spinner. Slipped the top of clip in slot on top of housing. Attached spinner and bottom of clip by holding top clip and pushing bottom of clip in place. No tools were needed.

Remove upper tray and spray arm. Remove two screws retaining pipe for upper spray arm and overhead. Unscrew retainer on top of lower spray arm and remove. Gently rotate the upper feed pipe clockwise until pipe can be removed from lower pipe. You may then remove the lower pipe and bearing housing where the seal is. Reverse order for reassembly. I also replaced upper spray arm bushing. Very simple, remove one screw and the arm will come out.

Removed first part of the broken part from the top rack of the dishwasher from below.

Removed the screw from the bottom of the sprayer arm to release the second half of the broken part.

Threaded new part in sprayer arm and replaced screw.

Attached part to top rack of dishwasher from below. This part was difficult. (The part appeared to be a little larger than the original.) It was a two person job, one person pushing down on the rack and the second pushing upwardand inward on the part it click to click it into place. Dishwasher now works great.

Pulled everything out the front, and dug down to find a thrashed chopper assembly (like a little garbage disposal). The previous owner just tossed anything in; pop tops, plastic cutlery, etc.
Didn't pay attention to the exact installation of the chopper as I pulled it out, but, it turns out that it only goes in one way.
Used pictures and instructions I found online as a guide and didn't have any issues.
Replaced the check valve because it isn't expensive and I was in the neighborhood.

I found instructions on line when I goggled my dishwasher name and model number with the words noisy door. There were three or four good suggestions at a couple of the sites I visited. I tried applying vasoline, then silicone to the rope where it travels through the plastic guides but that just cut the sound down about 50%. My dishwasher has plastic guides that look like rollers but they don't turn, they are fixed in place. The ropes squeak as the pass over the guides. The replacement part kit has plastic guides that turn like wheels now so the rope does not drag over them and squeak. This repair could be done by me in 20 minutes or less every time now that I know what I am doing.

I removed the black bottom metal cover then turned the nuts on the adjusting (leveling) bolts to lower the front end of the dishwasher so I could pull it out of the cabinet. Once I lowered is as low as it would go I opened the door and pushed down on it which tilts the dishwasher down and you pull out on it and the top lip clears the cabinet. If your dishwasher just pulls out the first time you try these steps may not be necessary.
Once the dishwasher is out the guides and rope are down at the bottom in the front by the door. It's obvious what to do to replace them.

Disconnect the water supply, the drain line, and the two screws that go up into the cabinet frame, then pull the dishwasher out from under the counter. Tip the unit onto it's face and the main pump/motor is facing up. Turn off the power then unplug the electrical connector from the motor. Remove the single bolt at the base of the motor then turn the whole motor ~1/4 turn counter-clockwise. A firm pull will remove the motor/pump at this point.
The new motor/pump has a new seal. See that the arrows on the pump volute and the motor frame are lined up before inserting into the housing. The new motor/pump slides into the housing easily and a 1/4 turn clockwise will pull it in tight. Re-install the locking bolt and revers the rest of the steps to get running again.

.The easiest way to complete the impeller and chopper motor replacement is to disconnect the power, water and drain line, remove the dishwasher from the cabinet, set the washer on its back.

From this point everything is visible, pump housing, motor, etc. and it's a matter of disassembly and reassembly. Make note or a drawing of where all the wires are connected so you reconnect them in the right spots.

Reinstall water lines and power and check for leaks before replacing shield or kick plate.

After pulling the dishwasher out from under the cabinet, I found it underneath near the back right side. I disconnected the old thermostat, unscrewed the clamp holding it into place, put the new thermostat in, screwed it back in and replaced the two plugs. Then I pushed the dishwasher back into place, and it initially didn't work until I found an online forum that was able to identify the reset command for my dishwasher (for the WDT710PAYM4, press any three buttons in a sequence of 1 2 3 1 2 3 1 2 3. After completing that all the lights lit up, and I shut the door leaving it for half an hour) Once the reset finished, the heated dry worked like it was suppose to.

The replacement of the gasket was simple and required only a flat-head screwdriver to push the rubber into the groove around the opening of the dishwasher. Took only about 15 minutes and the door is a tight fit now. I wish I had replaced the gasket 6 months ago when it first started coming loose when we opened the door to the dishwasher.

I looked up the most common problem with this model and it was the chopper assembly. I removed everything down to this. Sure enough, mine was broken off and the screen was completely clogged with debris. It was not difficult to replace, but it did take me a few minutes to slide it in to place. Ladies, you can do this. No need to call a repairman! Look up the repair manual and see where the assembly is. I had no idea it was even there. My dishes are spotless now.

I removed the screws around iner door panel. this allowed me acess to the hex head screws holding the plastic
air inlet and replaced it. the small tabs on the ends of the old inlet had bent
up allowing the water to flow by