66515987990 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Madison Township, PA
- Parts Used:
- 675806
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
dirty dishes
Installed pump kit. Was surprised the kit seemed different( some parts changed or deleted. Instructed to discard old parts and follow with new configuration. Reassembled and tried t fin it works fine now. Thank you so much
Was this instruction helpful to you?
Thank you for voting!
When the dishwasher started it would squeal.
Mine is a Ultra Wash 111
I followed the repair video on your site but my dishwasher was a little different. Not enough that anyone could still understand the video and not get it disassembled. The video shows two ball checks but mine doesn't use them where the videos shows. I put them in anyway because I called Whirlpool, who made my washer, and they assured me that they should be in there. They got sucked through the dump impeller and plugged the discharge tube so I had to disassemble it again and take the ball checks out. Lucky for me nothing got damaged. I then got a hold of someone on your chat line that got me to the correct parts view that shows where the ball check is suppose to go on my washer. During working on my washer I realized the squealing was because the bottom bearing on the motor needed oil. So all and all I'm happy because it runs quiet and it works fine. Thanks Greg
I followed the repair video on your site but my dishwasher was a little different. Not enough that anyone could still understand the video and not get it disassembled. The video shows two ball checks but mine doesn't use them where the videos shows. I put them in anyway because I called Whirlpool, who made my washer, and they assured me that they should be in there. They got sucked through the dump impeller and plugged the discharge tube so I had to disassemble it again and take the ball checks out. Lucky for me nothing got damaged. I then got a hold of someone on your chat line that got me to the correct parts view that shows where the ball check is suppose to go on my washer. During working on my washer I realized the squealing was because the bottom bearing on the motor needed oil. So all and all I'm happy because it runs quiet and it works fine. Thanks Greg
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from North Massapequa, NY
- Parts Used:
- W11164091
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The wheels that make the lower rack roll had worn out to the point that sometimes dishes would rub against the spray arm.
I removed the old wheel assemblies
(4 total holding 2 wheels each) with a slight prying with a screwdriver to
ease it off the rack. After the first one, the rest were a little easier.
The new ones had to "mate" a certain way and then just needed a push of the hand.
(4 total holding 2 wheels each) with a slight prying with a screwdriver to
ease it off the rack. After the first one, the rest were a little easier.
The new ones had to "mate" a certain way and then just needed a push of the hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from CHARLOTTESVLE, VA
- Parts Used:
- 675238
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
standing water in tub , not draining
removed old check valve from bottom of dishwasher and replaced with new one. I used channel locks to do this, disconnect hoses and screw out check valve, and put back in opposite order, make sure the dishwasher is empty of water or have a plastic bowl or such to catch water. Take off two front covers on bottom of dishwasher to access check valve ,white with hose attached.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phil from Jackson, MI
- Parts Used:
- W10134647
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
replace lower rack
compared it to old rack. Parts snapped together in 5 minutes. the fit was good. Kit did not include the silverware baskets, or the fold down narrow shelf.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Gladewater, TX
- Parts Used:
- WPW10253040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Prongs on Upper and Lower Dish racks were rusted and broken.
I ordered the upper and lower rack replacements PLUS additional wheels and other attachments because I could not tell from the schematic on the website whether or not the smaller pieces came with the rack.
As it turned out, the racks came ready to install and all it took was a limber nephew to take out the old ones and put in the new. Now I have plenty of spare parts in my own inventory in case the wheels, etc. need replacing.
I feel guilty sending you this repair story because all I did was order the parts on your website and then conned my nephew into making the exchange.
The parts arrived very quickly and in good condition. In fact, the new racks are an improvement over the ones that came with the dishwasher originally. Ms. Susan McNutt was quite helpful in keeping me informed of the status of the part that was back-ordered. It was a pleasure dealing with PartSelect.com.
As it turned out, the racks came ready to install and all it took was a limber nephew to take out the old ones and put in the new. Now I have plenty of spare parts in my own inventory in case the wheels, etc. need replacing.
I feel guilty sending you this repair story because all I did was order the parts on your website and then conned my nephew into making the exchange.
The parts arrived very quickly and in good condition. In fact, the new racks are an improvement over the ones that came with the dishwasher originally. Ms. Susan McNutt was quite helpful in keeping me informed of the status of the part that was back-ordered. It was a pleasure dealing with PartSelect.com.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Sterrett, AL
- Parts Used:
- 9743958
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old Tube Dry Rotted
1 Screw 5 minutes thanks for the quick service will definitely use ya'll next time
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Hollister, CA
- Parts Used:
- WPW10616003
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
soap dispenser spring wasn't working.
My husband replaced the entire soap dispenser until in under 30 minutes. I stayed out of the room. :) I didn't hear any swearing, so I assume it went fairly well. Sorry that I can't give you detailed instructions. He didn't need a manual or any type of directions. I guess it was kind of obvious how to do it. Just be sure you turn off the power first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanna from Smithtown, NY
- Parts Used:
- 675808
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Original supply tube for upper spray assembly disintigrated
Unscrew the top bracket on basket of upper spray arm assembly. Remove entire upper spray arm assembly. Remove old spray arm. Install new spray arm and new supply tube being careful to align the upper bracket with slot on new spray arm and supply tube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mario from Fowlerville, MI
- Parts Used:
- 4172127
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Suds and water leaking from bottom of door
Bent back metal ears over door hinge pins, released door springs from door hinges. Lifted door off of hinges and replaced corner drain back seals and lower door seal.Still leaks so obviously I have another issue or the door seal is lousy quality. I've completed this project before and never had another issue for 6 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Warrenton, VA
- Parts Used:
- WP8539324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Plastic Mount was broken for upper level.
We unscrewed the old mount, and installed new mount, inserted screw and tightened. Waa-lah, that was all that needed to be done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from DANVILLE, PA
- Parts Used:
- WP8539324
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken spray arm mount
Removed holding stew from old style bracket. Put arm together with new mount and installed screw. Aligned arm with upper rack and just clicked on. Ensuring spray arm spun freely and done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONALD from BETHLEHEM, PA
- Parts Used:
- WP8530929
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
ERATIC OPERATION, in and out of "child lock"
Followed the video. Only issue was that the panel mount screws cracked the plastic nibs that the screws threaded into. I replaced the screws with a Chrome sheet metal screw a bit longer and it held. Easy job!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leif from Seattle, WA
- Parts Used:
- WP8268816
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
All of these little clips broke over time
I read a couple of stories about how easy these are to break when installing. So I used extra care, and made sure to push carefully in just the right places.
What worked for me was raising the tines of the cup rack to apply some leverage as I squeezed the clips into place with my fingers. No tools. No broken clips. No injuries. No cursing.
What worked for me was raising the tines of the cup rack to apply some leverage as I squeezed the clips into place with my fingers. No tools. No broken clips. No injuries. No cursing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlie from Springville, AL
- Parts Used:
- WP8539324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Mounting hardware was broken
Removed the screw that held the mount in place. Snapped the new mount place (no screws required).
Fast & easy.
Fast & easy.
Was this instruction helpful to you?
Thank you for voting!