5871734569 Kenmore Dishwasher - Instructions

The repair was pretty straightforward. If somebody is attempting, they should make sure that screws close the bottom part of the door should be opened. You only need to open the top 4 screws.

Pulled the dishwasher out, turned it on the side to gain access to the inlet valve, removed the inlet valve. The hard part was getting the valve fitting that didn't come with the inlet valve. I had to use liqued wrench to loosen the hard water deposits to get it off. Once it was off, putting the new valve on was easy. Also of note, when I tested the old vlalve with an Ohm meeter it read 8 M ohm, not infinity. The new one only measured at about 1k ohm.

I pulled out the dishwasher and found the inlet tubing had a tear in the accordion part of the tube. I searched online for the model number and was directed to PartSelect. I ordered the inlet tubing, and it only took a few days to get to me. I then watched the video and was able to install the new tubing.

PartSelect is a life saver and I saved lots of money by not having to call a repairman.

Before starting I disconnected the dishwasher. First I removed the door cover which then exposed the interior part of the door. I then used a star bit on the screwdriver to remove old latch. I disconnected the four wires to the door making sure that I made a point of which wire was connected to what. I then inserted the new latch and reconnected the wiring. Finally, put on the door panel and screwed in the remaining screws. About 15 minutes total work time.

Take front off about 12 screws two screws held latch on took four wires off two white two black very simple to replace.

Removed the front cover by unscrewing the 8 screws. Removed the latch and attached new one. Re-attached front cover, and it works fine.
The gasket was in fine shape, and I question why I had to purchase the gasket in order to get the latch. Seems crazy and an unecessary expense on my part.

removed screws to loosen front door panel then removed the wire connection, then removed the broken latch with screwdriver, installed new latch in same manner, fastened front panel back with the removed screws and I was back in business, easy as pie.

First I removed the 5 screws holding the dishwasher door control panel. Then removed the 2 screws holding the broken latch. Then removed an electrical contact from the broken latch and installed to the new latch one contact at a time. Reassembled all in reverse order to completion.

First I removed the control panel and then removed the screw holding the handle. I then pulled the connector wires off and onto the new handle. I then screwed the new panel into place. Easy job, no mess.

Turned off water & pulled plug from electrical outlet. Two screws removed the lower cover, two more screws hidden behind the opened door allowed the removal of the bottom panel. Laid a towel under the valve on the lower left to catch water & disconnected the inlet fitting with a 1/2" wrench. Remove the two screws holding water inlet valve next. With valve loose, remove electrical connector and drain hose (pliers). Valve has an elbow fitting that will need to be removed and installed on new valve - use Teflon tape or paste for a leak-free assembly. Reattach the drain hose & electrical connector before installing the valve using the two screws. Once in place, re-attach the inlet fitting (no Teflon required on tapered seats) and make sure everything is tight. Test washer through one cycle for water flow and no leaks. If all is good, remove towel and tools, then re-install the two lower panels. Clean up and you are done!

This repair turned out quite easy. I removed the 6 phillips head screws that held the door latch cover in place, dropped the cover and let it hang while I removed the latch assembly that was held in place by two torx head screws. I used needle nosed pliers to gently disconnect the wiring connectors from the old latch assembly one at the time, then carefully attached the wire to corresponding lug on the new latch. Once all wiring was transferred, I installed the new latch using the two torx head screws, replaced the cover, and reinstalled the 6 phillips head screws to secure the cover. There was no need to replace the gasket, so I'm holding on to it for future use.

I used the diagnostic tool to determine which part I needed and ordered it. After receiving the part very quickly I took off the front panel easily enough and removed the old part as per video instructions. I realized it did not look exactly the same. I wasted a good bit of time calling both the parts co. and Fridgidaire to find out that there had been numerous problems with the old part so a new part was designed differently and therefore did not look the same but should work. Reviewing the video again I installed it and Voila the dishwasher was once again operational. The big mistake is I took the complete front part of the dishwasher off which took a while to reinstall. All in all the experience was a good one. Saved me money and God knows these days every penny counts.

After I received the Motor Shaft Kit I removed the spray arm tower and removed all screws, the center screw would not come out of the impeller, was stripped. Used a hammer and chisel to split the center of impeller and was able to remove. Also had to split the bottom impeller because it would not come out. All the parts that came in kit fit perfectly. Thank you Very much.

Didn't have a Torx screwdriver, but an Allen Wrench worked just fine. Also had to replace the gasket. Was worried about the fit of the door when closed with the new latch as the handle was very limp compared with the original. Also suspected that the new latch would cause the door to seat differently on the old gasket. Eventually found out from a repairman that the replacement handle does feel limp when the door is shut, and that they include the new gasket in case the old one is worn or that the new latch causes the door to seat differently on the old gasket.

I was recommended to try the latch and gasket kit. The latch was easy to remove and install.