5871734569 Kenmore Dishwasher - Instructions

Important - turned the power to the dishwasher off. took the screws out of the top part of the back door panel. pulled the wire leads of the broken switch, replaced the switch with the new one, reconnected the wires, put the panel back on.
Fixed

It was a walk in the park. Unscrew the six screws in the back of the panel to reach the latch. Unscrew the two torx screws in the front of the latch and replace each of the cables, one by one, in the new latch in the same order. Put the screws back into place in reverse order and... voila, wthout a single shock !!

I opened the control knob panel. The latch assembly is located behind inside the panel along w/ the wires. This is my second replacement of the assembly. The last one lasted about 2 years. They should make a sturdier latch assembly next time.

Removed the screws that hold the panel on ( just the top ones-no need to go all the way down the sides. Need a "star" headed screwdriver to remove the switch itself. Then removed the wires (4),one be one, so as not to mix them up. reinstalled all thescres for the switch, then the panel. Job done.
What amazes me is that Frigidaire doesn't read your page to realize that the handle assembly was defective and send out a recall. look at all the repars listed in your site , and these re just from the people that have responded with comments and who use your service. New handle/switch is much more sturdy with a higher density plastic that the original. Your service is easy to use, prompt and accurate. Fixed the dishwasher while my wife went to the store. Dishwasher done in 15 minutes and watched theNCCA tournament for 2hours in complete peace !!!!! No need to tell the wife only spent 15 minutes.

First i removed the screws on the back panel, unscrewed the latch, removed the wires and installed the new latch.
I found the latch is too expensive for a little plastic part.

Removed the screws on the inside of the door gaining access to the handle assembly. Lifted broken assembly out, inserted and secured the new handle assembly according to the directions.

The part was ordered and received the next day. The entire process was extremely easy. A repair person would have charged twice the amount of the part plus labor just to come out!!

First dissconnect power, and remove the 6 phillips-head screws from the back/upper side of the door, next remove the 2 torx screws holding the handle assembly, and unplug the 2 micro switches attached to the handle. Reverse this procedure and you're finished. It's so easy, a caveman could do it.

shut off the power on the breaker box, 6 screws inside the door on the tolp and side,pulled 4 wires off, 2 star head screws on the unit. took bad unit off,put new one on and put the screws back in.

5 minutes

Just pushed it onto the rod that held the old one

First, I located the dishwasher switch in the circuit breaker and turned it off, so as to kill power to the dishwasher - DO NOT PROCEED WITHOUT DOING THIS FIRST. Unscrewed front panel by removing 6 screws on the inside of the door frame. Then pulled 2 white wires on left and 2 black wires on right off of bottom of latch. Then used hex wrench to remove 2 hex screws holding handle and latch to frame. Then reassembled in reverse order as I disassembled. Note that there was a video on the site when I ordered the part, and it demonstrated all the steps; however, when I received the part and went back to the site to review the video again, it was gone. I'm glad I paid close attention the first time I watched it as it was extremely helpful and showed me exactly how to complete the installation.

Removed the old rollers with with screw driver. Used the original screws and washers, and reinstalled the new rollers. Had been having trouble with top dish rack metal slides popping out of the old rollers. I not that the replacement rollers are slightly larger and have slightly deeper groves for the slides. Have not had the new rollers installed long enough to see if they remedied the problem. Will know in a few weeks time. So far, so good.

Removed six philip head screws to remove upper half of the dishwasher door unit to access handle, then remove handle by remove two star screws and for wires connectors. Installed in reverse.

Note:
I was very impressed on how quick I received the part after it was ordered.

After watching the repair video, it was 'easy as pie'. I would have thought the gasket was too long and cut it off if not for the video. Thank you. Saved a great deal of money not having to have a repair person do the work. I strongly recommend watching the video.

Removed the screws holding the door panel and as the sheet said was the way the it went. Two screws holding the handle latch and replaced it and put the door back on. There was 4 wires to replace on the latch. Replaced the gasket and the job was done. All in all it was a very good experience with good instructions and very good same day shipping. A VERY GOOD EXPERIENCE.

I replaced this latch,but noticed that the electric terminal configuration was not identical to the old original part. There were no installation instructions furnished for installing this new part, so I had to guess that the wire terminals attached to the new part in a similar position as detached from the old part. So far the renter has not called that the dishwasher is not operating correctly.