58715074200 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Spring on Door Broke
I took the door off by removing the two screws that hold the it in place. I removed the two screws that secures the diswasher to the cabinets. I slide out the unit approx 3 inches. I attached the new spring and linkage (very simple to see how it connects).
I pushed the unit back in, secured it to the cabinet and put the door back on.
That's it! Easy. I saved at least $150 service call with Sears.
I pushed the unit back in, secured it to the cabinet and put the door back on.
That's it! Easy. I saved at least $150 service call with Sears.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Milford, MA
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dish washer leaking at the door
Pulled off the old gasket and replaced it the same way with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andre from La Mirada, CA
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking Dishwasher
The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Fort Washington, MD
- Parts Used:
- 154662601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dishwasher door strike piece broke. Door had to be propped closed each time dishwasher was used.
Took out the two retaining screws and pulled the unit forward. Took the old door strike out and put in the new one. This site is where I go for all my appliance repair parts!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mena from Sarasota, AL
- Parts Used:
- 5304535382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cutlery basket
Simply took the old one out, and put the new one in.
Was this instruction helpful to you?
Thank you for voting!
the door spring broke
there were two screws securing the dishwasher to the counter top, I took those out and pulled the dishwasher out about 12 inches the spring and plastic linkage was visible, I just unhooked the one that wasn't broke and installed the new linkage and spring the same way it came off the one that was broke was even easier i just looked at the one that wasn't broke and put the linkage and spring on the same way, I pushed the dishwasher back under the counter top and put the screws back in took about 10 to 15 mins I am an ex-mechanic so I am pretty fast anyway.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Chicago Ridge, IL
- Parts Used:
- 809006501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Bottom Of The Door Was Leaking
First of all, I got the part 24 hours after I ordered it. That in it self was a feat. Second, I followed everyone elses instructions, pulled the old gasket out with a pair of needle nose pliers, cleaned the area as good as I could, found the notch for the slot on the gasket to slide into and viola...it slid in and stayed in. No more leakage whatsoever! Thanks for all of the tips!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAN from PLYMOUTH, MN
- Parts Used:
- 5304463777
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Water Not Draining
Unhooked the dishwasher and took it out. Laid the dishwasher on it's back. Located the drain pump and took it off. Put the new one in it's place. Hooked the dishwasher back up and tried it out. Everything sounded and ran good. Easy assembly. Took 30-40 minutes if that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALBERTA from FAIRBANKS, AK
- Parts Used:
- 5304532229
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
wheels break or bend or fall off
if the wire they snap on was bent it needs to be straightend.......they just snap on. easy to install but wish they had better wheels so this problem would be solved. My 2 sons have same brand dishwashers and have same problem.
Was this instruction helpful to you?
Thank you for voting!
broken springs on door
pulled of dishwasher a couple of inches,
installed springs
pushed dishwasher back
done!
installed springs
pushed dishwasher back
done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from TREVOSE, PA
- Parts Used:
- 154574401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dispenser cover wouldn't stay closed
Removed two screws,one on each side of the bottom part of the door. The door cover then comes off. Then 6 screws hold on the dispenser. Shut off power and remove two wire connections. Replace dispenser. Replace lower door cover and two screws. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from MARSHALL, MI
- Parts Used:
- 5304523457
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers
Water inlet tube had worn a hole in it
Removed old hose and went to install new hose from Part Select. Part received was not the same as advertised. It was 6-8 inches shorter than the original hose. Would not make the necessary turns because of shorter length. I even went to Video instruction on installation even though I have been in Machine repair for 30 years , this video showed using the shorter hose and when installed in the video hose also had a kink because of hose length. Had to stop repair and go to hardware store and purchase a longer hose. This purchased hose from the hardware was 50% cheaper and actually worked. I also paid for 2-3 day shipping and received part 7 days later. I am very disappointed with Parts Select and am an owner of an Equipment Rental Facility and will never utilize Parts Select again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from MOUNT AIRY, MD
- Parts Used:
- 5304507405, 5303943103
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
One screw that held the roller would not hold as the hole in the case was stripped. I knew when I removed original as there was material in the screw threads
I used both epoxy on the male threads and then pulled out the case and twisted the flat car body flat kind of a nut. Let it sit for 36 hours and now like new.
Was this instruction helpful to you?
Thank you for voting!
The bottom door gasket and tube gasket were leaking. The rinse aid cap was broken.
I removed the door panel and ran the dishwasher to determine where it was leaking. Ordered the parts. When parts arrived I removed door in order to get at the bottom door gasket, replace it, and removed the tube gasket and replaced it with new parts. The whole job was very easy for a person that's never repaired a dishwasher before. I also found that the return tube gasket at the top of the dishwasher was leaking and repaired that by making a new gasket out of a flat piece of rubber and an o-ring. All leaks have been repaired. With regards to the return tube issue, it may have only been loose and if so, I could have just tightened the return tube outlet and gotten the same results. The people at this site were excellent. Thank You
Was this instruction helpful to you?
Thank you for voting!
one door spring was broken so it fell open easily
it was simple. I followed the instructions of an earlier post on this site, I took off the bottom front door cover, crawled down, and replaced both springs and both clips, it is like new now!
Was this instruction helpful to you?
Thank you for voting!