66515898790 Kenmore Dishwasher - Instructions

The old spring on the detergent dispenser box door failed and the dispenser door would not pop open at the right time in the wash cycle.

Ordering the new spring was easy on the website. Need dishwasher model number, stock number and serial number.

Hint - Order at least 2 springs! They are not expensive.

I followed the instructions in the video. I could get the spring on the spindle correctly but could not get the two spring prongs to catch to create spring tension on the door without using a thin knife blade to carefully push each prong to where it caught on the dispenser door.

I needed to slide the prongs slowly and carefully to get them to catch on the door. This distorted the spring. That's why you really need two springs. I then used needle nose pliers to pull the latching part of the spring to catch on the inner door. That distorts the spring, too.

So you really need two springs. One spring to learn how to do it and a second one to replace the one you distorted as you learned.

Take care

I ORDERED THE PART THAT WAS EASY BUT WHILE THE MACHINE WAS USED FOR HOW LONG I DON'T KNOW WITH OUT THE CAP IT GOT FILLED WITH FOOD AND JUNK. FIRST THING I HAD TO DO WAS EXAMIN THE DOOR AS TO HOW I COULD CLEAN THIS THING OUT. I REMOVED 6 SCREWS THAT HELD THE DOOR TOGETHER AND PULLED EASY CAUSE I DIDN'T KNOW WHAT I WAS GETTING INTO. NO PROBLEM THERE WAS NO ELECTRIC PLUGS HOOKED TO THE DOOR. I TOOK IT OUT SIDE AND STARTED USING VINIGAR AND POURING IT INTO THE HOLE AND SHAKING THEN TRYING TO GET IT BACK OUT. WELL THERE IS ONLY ONE POSITION THAT WILL LET THE VINEGAR BACK OUT. I HAD TO HOLD IT SIDEWAYS THEN TILT FORWARD AND IT WOULD RUN OUT AND BRING SOME JUNK WITH IT. THIS WAS A TIME CONSUMING PROCESS BEING YOU COULD NOT SEE INSIDE TO KNOW HOW MUCH JUNK WAS IN THERE. JUST POUR AND DUMP. AND DON'T FOR GET TO SHAKE TO LOOSEN ANY THING LEFT INSIDE.LOL I WAS VERY PROUD OF MYSELF NOT KNOWING FOR SURE IF I FIXED IT OR NOT BUT I TOOK A SHOT I HAD. I DID SOME SCRUBBING AND DEGREASING ON THE UNDERSIDE OF THE BOTTOM OF THE DOOR BEFORE I REASSEMBLED IT. THAT WAS EASY AND I CROSSED MY FINGERS ANY WAY. I GOT OUT MY NEW PART AND THE JET DRY I BOUGHT AND STATED TO FILL THE DISPENSER AND IT TOOK HALF THE BOTTLE.YEA !!! I PUT THE CAP ON AND COULDN'T WAIT TO DO A LOAD OF DISHES. EVERY THING IS LOOKING GOOD NOW. THANK YOU PART SELECT FOR MAKING GETTING THE PARTS I NEEDED SO EASY AND SHOWING DIAGRAMS SO I HAD THE RIGHT PART. I COULDN'T HAVE DONE IT WITH OUT YOU.

Pulled the old gasket out with needle nose pliers, cleaned the slot for the gasket, installed the new gasket, needed no tools. This repair took 5 min.

Removed the plugs in the slides, removed the rack, slid the new rack in and replaced the plugs.

There was no tools involved the part popped right into place. I received the part within two days from the date placed. It was great.

I screwed the rack mount to the spindle using
the extra screw I ordered. I removed the upper dishrack's front stops and slid the rack
out. I clamped the mount to the dishrack. I screwed the rotor to the spindle with the screw that came with the rotor kit. I slipped the feed tube mount over the end of the tube and clamped it on the dishrack. I replaced the rack in the slides and replaced the front stops.

I had a hard time driving the screws. The slots are crossed but do not seem to be standard Phillips. The screws were hard to drive into the holes in the hard plastic. Before I could drive the mount screw all the way, the slot was too stripped to use.

I bought the kit because it had other parts that I thought I needed.

I first had to take the upper drawer of the dishwasher out so that I could get to the faulty part. This was a little tricky as there were two clips that had to be removed from the arm slides before the upper drawer could be removed.
I then realized that the faulty part DID NOT exactly match the repair part I received. The original connection wand was in two pieces where the repair part was all one piece. That required a bit of thought before I began the repair. There was NO drawing accompanying the new part, so I had to decide how the part would be connected. After a little trial and error, I determined the arrangement of the repair part and completed the repair. All in all, it went well, but there was a few anxious moments when I first saw the difference between the original part and the new part.

Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

Removed old rack opened box inserted new rack. So simple sorry I waited so long to replace.

Took out old rack, put in new one. Part arrived on time and was an exact match to the original.

Easy fix. It’s a screw on by hand piece.

I just had to unscrew the old nut and screw the new one and install the new wash arm bearing ring.

I guess some food got caught in the water level sense float and caused it to mal function.
In the diagnosis process, I removed the arm to clean out any debree in the strainer ( found broken glass). I also found that the two rings mentioned above were worn. I replaced them and all is well.
Thank you for fast response with the replacement parts.

door gasket old the vent was pluged up full of black slime cleaned out and door stopped leaking