36314382000 Kenmore Dishwasher - Instructions

Ordered the part online and replaced the hoses. Very easy...took maybe 20 minutes

Read directions. They were poorly drawn. Set them aside. Opened up unit on December 26th. I made careful observation of the wiring, two hoses, one metal bracket, the hose two clamps, and then proceeded. Instructions said 1 to 2 hours, to complete. Ha Ha, perhaps if you've done it before. It was actually really closer to four hours. When done, it worked perfectly. The best part, my wife said: "This was the best Christmas present ever!" That made my day! Dishes are clean again, just like new! Thank you: www.PartsSelect.com.

I watched several YouTube videos on how to make the repair. It looked very easy but sometimes professionals, because they've done it before, don't point out small tips that would help a DIY homeowner. The latch goes easily into the inner door slot but there's nothing to hold it there. The videos show the inner and outer door being closed together without showing that you have to hold the latch in place while bringing the outer door up to meet the inner door. Any movement of the inner door makes the latch fall out. So I would say it took me 5 times longer to do this repair than it would if I was doing it again.

The video was extremely helpful. Removing the tabs was easy. However, we struggled with the re-insertion. They did not "snap" back in as easily as seen on video. We ended up using a pair of pliers to push pieces into slot. We did not use very much pressure for fear of breaking the plastic. However, after many tries, we were successful & it works perfectly. Perhaps a close-up of the "snapping in" part might help future installers.

Put on a new cap.

According to instructions with part

very easy old part out new part in direct replacement, fit right in and it is working. Great deal and about half of the price than ge website. Thank you.

Looked up possible causes on your website. Website stated that more than 50% of time the cause was the piston and nut assembly. Removed the piston and nut assembly in bottom of unit behind screen on rear wall and saw that the gasket seal was completely gone . Ordered the part. took less than 10 minutes to install. Tested the unit and it drained completely. Thank you as i was looking at a more difficult repair if the pump had to be replaced.Repair cost less than $20.00.Before changing piston and nut assembly I cleaned the strainer and sump. disconnected drain hose and checked for blockage . i than checked your website that listed the piston assembly as the culprit more than 50% of the time. Thanks again

Unscrewed old one and installed the new one.

A short investigation revieled that one of the wires going to the malfunctioning switch was burnt and the connector had come loose from the switch assembly. The old assemble was replaced in a short period of time and all is well.

Inside door panel off

I first made a bad assumption that the leaking dishwasher was from the gasket. I replaced the gasket and it still leaked. To find the leak, I took the body off of the dishwasher and ran it to find the leak. It was from the solonoid connection. I took photos of the leaking motor unit and very easily replaced the new motor unit by matching the placement from the photos. The hardest part is tipping the dishwasher on its side and mopping up the water.
It was very easy. All you need is a nut driver and a Phillips screwdriver. Even an over-domesticated, non- tool user can do it.

Ordered the new motor/pump here at parts select and with the easy directions I replaced in no time flat. Saved me $300.00 for a replacement.

Our older GE dishwasher was leaking water on the floor while running. After inspecting it while running I was able to determine that the water was coming from the seal around the motors shaft where it entered the pump. I then looked up the washers model number and ordered the impeller shaft seal kit. To my suprise the kit arrived the very next day! After disconnecting the power and water supplies from the dishwasher , I then removed it from the cabinet base and turned it over to gain easy access to the bottom. Using nothing more than a nut driver, adjustable wrench and a pair of pliers I was able to loosen the two compression clamps and two hose clamps that hold the pump to the bottom of the washers tub. I then removed the entire pump and took it to my work bench for the rest of the repair. Removing the plastic impeller strainer was the toughest part.. Lacking the proper spanner wrench, I had no tool that would lock onto the raised tabs to turn it loose with. I was able to position the tabs in the jaws of my workbench vise and giving the entire pump a little twist, It broke free and I was then able to unscrew the rest of the way it by hand.. The old dried up detergent made for a good adhesive, and after removal I cleaned the area completely so the new strainer would thread in easy. I installed the new parts in the kit as per the supplied instructions and re-installed the pump housing back on the dishwasher and put it all back in place. After running it several times not a drip was to be seen, and I was very pleased with the whole process. With the shipping it cost me just $25.00, and it saved me a expensive service call or maybe even the cost of buying a new machine. I would say that overall it was a easy repair but lacking the right tools, you may have some trouble removing the pumps plastic strainer screen as I did. I would highly recommend PartsSelect to anyone, and the entire experience was a good one for me.

Turned off electical and water - took fillter screen out of inside, unscrewed cap took out valve and replaced it