36314382000 Kenmore Dishwasher - Instructions

I found that the supplied part did not have threads to receive the bolts that were used in the original part. I had to locate thin nuts and bolts and very awkwardly fit those in behind the part. The orignal part would have just bolted on from the front. I almost returned the part as unsatifactory, but decided to make do. Otherwise it would have been a 10 min job.

I pulled the dishwasher out and detached the drain hose. I attached the new drain hose after cleaning out the connection to the garbage disposal.

Now my dishwasher doesn't stink anymore!

It is pretty easy to replace the parts because the new and old parts are identical. I unplugged wire connection, removed the two screws and one small metal piece that fixes the plastic moving part, then put back with new parts.
A little bit extra time may needed due to small space in that location, also the small or flexable screw driver is needed.

Heard a noise in our dishwasher and ended up taking the entire pump and housing out and found a small sucker stick in the impeller along with a bunch of string and other material that needed to be cleaned out. Also found that the housing was leaking at the shaft that goes to the solenoid and dripping on the solenoid and had rusted the metal plunger that goes into the solenoid. Bought the housing and solenoid unit. 1 screw (bottom one) on the housing was rusted becaue of the water. Had to hacksaw the housing and then had to drill out that screw. Also, the pump housing screen is left hand thread and is tough to get out. Had to hacksaw that too. Be careful of the orientation of the metal ring in the impeller area. I did that backwards the first time and the motor would not move. Also, the electrical connector to the motor appears to be polarized so it can only go on 1 way-notice before you take it out. Be sure to screw the solenoid bracket back on tight and notice the spring orientation before you remove-the new one was different than the old. Bottom line is that it works fine, and for $40, it's fixed, rather than spending $800 for a new one.

Opened the package and screwed in the new rinse aid fill cap. No problems. It fit and works just fine.

Pulled unit out from counter (never had dishwasher issues before) to see if there was anything obvious with wiring or anything. Noticed that some little piece on the bottom looked to have melted (later discovered to be the drain solenoid). Removed the obviously defective part and looked it up on line. Found the name of it on Part Select's website then started shopping for best price. Came back to Part Select because the price was the cheapest I could find. Two - Three days later received part and put it back on and had the dishwasher back in place and in use within about 10-15 minutes. Marking my first ever dishwasher repair. :)

My son found a water leak and cut the water supply off. He then pulled the machine from under the counter at which time I examined the valve under pressure and saw the leak. We cut the water off again and after tripping the circuit breaker we pulled the electrical connector and undid the mounting bracket which made getting the lines off the valve much simpler. New valve in hand I attached the lines and did a test then remounted the bracket and attached the electric. Easy as pie!

At first I found some water on my hardwood floor by the dishwasher, I thought that I might spilled't the day before, then it hapened again, so I remover the front lower cover for the dishwasher and I found water under the dishwasher, then I turned on the machine and I found a pin hall water leak from the water inlet valve. I turned the machine off, then I closed the water valve under the sink, then I disconected the power plug from the valve, the diconected the water supply copper pipe, then diconected the house from the valve to dishwasher, then got the part# from the valve sticker and the model# for the dishwasher from inside of the door. after that I went online and I got the valve. make sure to try more than one website because they all have differant prices, and Parts Select was the lowest one.

I removed the scews holding the inside door to the outside door section. Once removed I removed the 2 screws that held the switch to the door. After removing this switch I had to open it up to expose the four wires on the switch. I reattached the four wires to the new switch closed it up and placed it on the door with the 2 screws.
Replaced the inside door. Job finished with the switch working and the dishwasher operating as per the factory standards.
Very easy job and by doing it myself I saved money on a service call.

replaced solenoid. worked properly after repair

Once the new motor and pump kit arrived. I removed the dishwasher, turned it upside down and replaced the motor and pump with the new one per the directions. Difficulty came in feeding the electrical wire/plug back through the cabinets. Once done, turned on the dishwasher, filled the tub, then manually moved the dial to drian. The water still would not drain from the tub. I searched further for the problem. Here it is; Found the air gap tube was plugged with food. Once I removed, cleaned and reinstalled the air gap, the tub drained fast and everything works great. So, I hope you folks put this up in your troubleshooting section for others to check before buying a pump and motor kit. If you had, I would have been able to check out the air gap, clean it out first before spending $140.00 for a pump and motor kit I didn't need. Anyway, lessons learned..Jeff

Replaced with a new rinse aid fill cap.

Removed 4 screws, took off basket covering, put new part in one turn, then replaced covering. Plumber had come out, I watched what he did, he had to order part and come back. I asked how much he didn't know but said cheaper than buying a new dishwasher. When he left I started calling around about the little plastic part that I needed. Part was $15.50. They called and said it would be $110.00. Needless to say I called them out and ordered the part myself and put it in. Took me like 6 minutes and cost $21.69. I was so mad about this situation that I even got my service call money back that I had already paid.

Removed the old one from its slot and slid the new one into it.
No instructions needed.

I used the website to identify a few different problem areas. I found that the motor shaft would not turn. Upon removing it, it did turn, which lead me to look at the Impeller which was worn / frozen. Ordered new impeller and installed 100 % success !!!