6651744990 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jane from Sebring, FL
- Parts Used:
- 4387043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Detergent door would not spring open-spring was broke
Put on new door, making sure the spring was set to flip the detergent door open in order for the detergent to properly do the dishes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Cameron, NC
- Parts Used:
- WPW10254672
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
changed out kitchen sink faucet set
replaced the faucet adapter I did not save when I change out the kitchen sink faucet set
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Becky from Stanley, NC
- Parts Used:
- WPW10254672
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
The Faucet Adapter was worn out.
Ordered a new Faucet Adapter! Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from Brooksville, FL
- Parts Used:
- WP3368999
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Soap dispenser not opening
Took inside door panel off. replaced spring that opens soap dispenser lid during cycle. Put inside panel back on. Works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from FORT FAIRFIELD, ME
- Parts Used:
- WP8274220
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench set
I Was Not Geting The Water To Run Thou My Dishwasher
I Tip The DishWasher On To Its Side So I Could See Under The Dishwasher .I New The Moter Was Working Fine. I Could Here It Runing While It Was Upright . So I Determind That It WAS The Water Inlet Valve . SO I Used A Pair Of Plires To Pull Back The Clamp On The Hot Wate Hose. I Took The Hose Off . And Then I Unscrow the Hose On The Water Inlet Valve That Takes The Water Out Of The Dishwasher.I Then Used A Small Werench To Take Off Two Small Scrows Holding the Water Inlet Valve To The Dishwasher .I Pull Out The Old Water Inlet Valve I Then Found The Modle Number And Seriel Number To My 20 Year Old Whirpool Dishwasher . I Then Went On Line Useing The Name And Numbers Found Partselect And Orderd The Right Part And Put The New Part In .It Took Me Less Than 15 mins And It Saved Me Maybe A Cupple Of Houndred Dallors..Thank You Partselect..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Colorado Springs, CO
- Parts Used:
- 676413
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Old whirlpool soap dispenser latch wasn't working
Bought a house and with it can an old whirlpool dishwasher in where the soap dispenser lid would latch, as the latch itself was gone. Ordered the latch from part select and used the installation video to switch the latch out. Only problem I came across was that the torx screws at top of he door were free spinning. Ended up using a flat head for leverage to finally get the screws out. Everything works perfectly for once.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Rehoboth, MA
- Parts Used:
- 676413
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Latch worn out
Followed vidio instructionson web site. Quick easy fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- perry from cynthiana, KY
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
detergent dispencer door spring and pin worn
I installed the opener spring in the direction it was needed to open the door then installed the pin. I placed the door in the position it goes and took a pair of pliers and squeezed the pin into the pin slot. the spring has to be forced into a tension position. I did this by sliding the spring to one side and forcing it into position, the other side is done the same way. works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Republic, MO
- Parts Used:
- WPW10082894
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Heating element would not heat
I watched the video, read all the post, they all said change the heater. So I did. Only there is a little fuse at the back of the unit that also goes bad and that was my issue. Have it ordered and will be going soon. That said, Part Select made finding and getting my parts a breeze!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrel from rosamond, CA
- Parts Used:
- WP8066018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lid Spring
Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Little Rock, AR
- Parts Used:
- 676413
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Top of the Soap Cap Latch was broken
The top of the latch was broken on I had to push the plunger back through the mounting to get it out. ai had to pull the whole assembly apart to get the locking nut out. i remove the latch assy and took about 10 minutes to figure out how to put it back together. Changing it with the help of the video wasn't hard but confusing at times. Thanks for the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Woodward, IA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dishwasher leaking in lower front door area
Removed and installed new door gasket which I found to be a simple task. Ran dishwasher and it still leaked. I then looked at other repairs submitted by your customers with the same problem. One had mentioned removing the lower spray arm and checking the screws around the pump. Sure enough, 2 screws were nearly ready to fall out and all others were loose. Tightened those, reinstalled spray arm, ran the dishwasher and no leaks. A big "Thanks" to you and also to other customers for sharing both their problem and how they were able to fix it. It sure saved me some money!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- matt from grant park, IL
- Parts Used:
- 676413
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dish washer soap drawer would not work
we followed your instructions submitted via e-mail and they worked out just fine....thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Charlotte, MI
- Parts Used:
- 4318050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Broken door spring
The repair was very simple. Simply pull the dishwasher out far enough to access the springs, remove the old with pliers and install the new springs in the same spot as the old ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from SELKIRK, NY
- Parts Used:
- 4318273
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bad door switch
i took the inside door off and took the 2 switches out and replaced them; not too difficult.
Was this instruction helpful to you?
Thank you for voting!