6651778582 Kenmore Dishwasher - Instructions

You need a properly sized hex (Allen) wrench to get the screws out. Basically simple: remover bottom roller tray, unscrew large plastic holding bolt, remove lower spray arm, unscrew bolts (be sure the wrench is sized right or you might strip the heads), and replace gasket; then reverse procedure. Chances are if the gasket was bad, it will be very obvious (out of circular slot and stretched).

Turn off the breaker to the dishwasher - there will be water very near the motor and other electrical components. I first scooped and towelled all the water out of the bottom of the dishwasher. The drain valve can be accessed from the bottom front of the dishwasher without pulling the unit out from under the counter. There were 4 screws to remove the 2 bottom metal panels. Next use pliers to loosen and slide back the hose clamp connected to the drain. Have a towel ready and pull the drain hose off the white check valve. The check valve can then be removed by unscrewing it - you may need to use pliers. Put the new one on and everything back together.

popped off the old rollers + tracks; then snapped on the new ones; as my granddaughter would say "easy peasy lemon squeezy". Took hardly any time at all. :-)

Found the adapter on Parts select through a google search. Unscrewed the existing faucet aerator and srewed in the adapter. The plastic shrink wrap holds the washer and screen in place, so don't open it until you're ready to install. Finger snug does it, only use the pliers to remover the old aerator from the faucet. Normally, I don't use pliers, but both of these parts were round and had vertical serrations to engare the plier teeth.

Removed cover and broken spring ,installed new spring and cover.Did it all in less than 10 minutes

I installed the opener spring in the direction it was needed to open the door then installed the pin. I placed the door in the position it goes and took a pair of pliers and squeezed the pin into the pin slot. the spring has to be forced into a tension position. I did this by sliding the spring to one side and forcing it into position, the other side is done the same way. works great

I looked in the bottom of the dishwasher after browsing the website regarding possible solutions. When I removed the bottom spray arm I noticed three screws missing from the pump housing. The loose pump outlet had allowed the seal to push out. Ordered-Normal shipping on the part.

I simply looked at the remaining spring to see which notch it needed to be attached to. I went in very well using a long needle nose plier. Works great.

Unsnapped the old rollers and snapped in the new ones. Worked great and easy. I was very pleased that the parts came so soon as well. Thank You, Ms. Cason

Used the diagram and disassembled and reassembled.Used most parts that were in kit as it also fit other models and did not need all the parts.

Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install

I ordered door cover kit #4387043. It comes with new door cover (lid), new pin, spring, latch and snap. Two problems I encountered was 1)with the spring - there is a trick to replacing it. I had to look up how to put the spring on properly. Go to YouTube and Partselect "Dishwasher Repair - Replacing the Lid Spring (Whirlpool Part # 8066018) " will show you the trick. Was a cinch after I knew the trick. 2) you must take door apart to replace snap that goes with the latch, so you might want to replace the detergent door first and see if that solves your problem without changing the latch. It is workable, but I had to go on line and look for diagram to put back together. Just frustrating but for less than $20.00 solved the problem. Good luck.

My model was DU7600XS0. I disassembled according to the video and the parts diagram here. I found a piece of metal, a pebble, and a wrecked drain impeller. I cleaned out all the debris and began reassembly. I found that the chopper blade shipped with this kit has a lip and will not fit over the metal drain impeller sleeve on this model. It needs to, or else it will not screw together properly and the impeller will not be able to turn. My old one was undamaged, so I used that instead. Also, the large black wash impeller has a shaft that is longer than the original part and because of that, it would not screw on. Again, the original wash impeller was fine, so I used the old one. I replace the gaskets and screwed everything else back together. It works great now. No water is left after the cycle anymore and the sound it makes is back to normal. Money well spent on this kit!

Heard a grinding noise in our dishwasher one night recently while it was in the drain mode. Water wasn't draining out so I had to siphon it out with a tube, cup, and rags, then looked up information about the washer/dryer on the internet and found PartsSelect. I watched the repair video they provided and decided to give the repair a try. I began to remove all the necessary parts following the instructional video.
The hardest part of the job came early on, and once that was completed the rest of the job was a cinch. The center screw holding the upper impeller was the hardest part to remove. I tried to use the adjustable wrench on the hex shaped nut molded to the impeller while turning the screw, but that old screw was so tight I was afraid I'd strip the molded impeller nut.
I then tried a 1 inch nut without the driver attached to it but with a pair of vice grips clamped at about 45 degree angle on the 1 inch nut and set on the molded impeller nut while at the same time trying to remove the screw by putting the small nut driver through the top of the 1 inch nut and turning it. No luck there either. It would not budge.
By this time I was entertaining the idea of buying a new 5 to 800.00 dishwasher.
Well I had nothing else to lose except 5 to $800.00, so I reverted to caveman technology.
I ended up using a small chisel and wood mallet to get the impeller off the shaft. Since the impeller is made of a rubber like material, it came off easily in pieces using some careful strikes with the hammer on the impellers molded nut. When this was complete, I unscrewed and removed the filter housing.
The impeller screw, which was still in the motor shaft, and was removed 'after' this because there was no impeller or filter chamber in the way. There was a small space between the screw and the motor shaft since the impeller was removed from around that screw so I first tightened it a little bit, then finally was able to loosen the screw. You would think that screw had been super glued into that shaft but it finally came out. After that I removed the chopper blade and found that the spring attached to it was bent and had tore the shaft of the 'lower' drain impeller to pieces. After cleaning up the impeller pieces I ordered the drain and wash impeller kit from PartSellect. It arrived in a couple of days and the new parts installation went quickly.I was especiially relieved that the new screw and impeller went on without a hitch.
I didn't use the new shaft seal provided because it was a different height then the original seal and wouldn't allow the cover to the drain impeller to seat properly. The height of the new seal also caused the new drain impeller to push or spring up too high.The original seal looked fine so I used that and it worked just fine also. Started the dishwasher up for a test and it all worked flawlessly. No noise no leaks. This was my first washer dryer repair. Following the Part Sellect instructional video with Steve explaining while doing the removal of old and installation of the new parts was a breeze. SO, here's my conclusion. Folks, for under $50.00 I saved a lot of money and expect that I'll get at least a few years more use from this old dishwasher. Thanks again to PartSelect and Steve for your help.

The dishwasher was making grinding noises and then stopped draining at all. I was able to follow the video directions and replace the parts from the drain and wash impeller kit, but it did not solve the problem. Must be the pump or something else. Was worth a try and partselect.com was good with service and price.