66516539200 Kenmore Dishwasher - Instructions

I removed the dishwasher from under the counter. This took the bulk of the repair time along with disconnecting the water supply and electrical connection. I had enough slack in drain hoses that I could turn the dishwasher over to replace the motor. I was surprised that there was only one bolt that held the motor in place. I put the motor on, turned the dishwasher upright and slide it back unde the counter and began the long process ofreconnecting everything. I am sureit could have gone faster if I were younger and did not need glasses for close work. Start to finish took me four hours. This was the fourth time I have replaced motors in dishwashers of various makes.

Looked at other side of top rack which still had the stop. Just had to orient the direction of the stop and push it firmly onto the rack arm. Took a couple tries, but it went in and locked. Works perfectly. Inexpensive and easy fix to to very annoying problem.

Found the gasket to be wearing out. Once I got the part I took everything apart inside to find that I could have just taken the dishwasher out and replaced from the bottom. It was not difficult, but I've installed a ton of dishwashers. For the average homeowner, this is can be a difficult job since it requires plumbing and electrical skills.

Replaced the switch, that did not fix it, but a new circuit card did

I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.

Pulled front panel and replaced door switch. Extremely easy but did not fix the problem.

I unscrewed the dishwasher from the counter (two screws under the countertop), and pulled it out about a foot so I could access the friction sleeve. I used a needle nosed pliers to slip a spring latch off the door. Then I slipped the new friction sleeve on and reattached the spring. Tested the door. Success! Super easy. About 5 minutes of work.

Our Kitchenaid dishwasher was leaking so I called a repair service. I gave the model number and serial number over the phone and explained the problem. I was told the rubber gasket would need to be replaced. When the repairman came 5 days later he told me that the gasket needed to be replaced but he didn't have a new one on his truck. He ordered one and said he would be back in a week to repair the dishwasher. That took 10 minutes at the most. He then gave me a bill for $200.49 ($71.49 for the part and $129 for the labor)that I had to pay right then. I wrote him a check so he would leave and immediately called the repair company to tell them the price was outrageous and that I had never before paid for a repair before the work was done. I was simply told it was their policy. I then told them I was stopping payment on the check - which I did. I checked on-line for the part and found your web-site and the the part I needed for $27.62. I ordered it on a Monday, it arrived on Tuesday and my husband easily installed it that evening. Thank you, thank you, thank you!

The old tine row came out easily and the new one was easy to pop into place. I was pleased that it was so easy to order a replacement part.

Removed the old tines by pushing out the clips on the end and then installed the new tines and applied clips - took 10 minutes worked slick and the washer basket looks to be brand.

put new hose on, very easy.

PartSelect found the right part for me on the first try. I had scoured the web looking for this particular drying agent cap. Even Sears said I'd have to order the entire dispenser assembly - $$$!

PartSelect found just the cap I needed at a much better price.

Fantastic service. Shipping was faster than promised. I can't say enough good things about them!

Removed required hardware and dishwasher from undercounter mount. Turned dishwasher on its front and removed the old motor. Installed the new motor and tested for function. Installed once test was successful.

I took the unit apart to find out what was making the loud noise and found the seal on the main pump had been leaking ito the bearing on the motor.

1. Opened inside panel (about 8 screws)
2. Checked wires to see if we had power, which led me to the fuse.
3. All wires were hot, so I bypassed fuse straight to the motor, which worked.
4. Took out the fuse, didn't really know for sure whether it was bad yet, googled the part number and it led me to PartSelect.com!
5. Ordered part (it arrived in two days!) and replaced existing fuse and WE ARE WASHING DISHED AGAIN!!