2213804N710 Kenmore Dishwasher - Instructions

unscrewed dishwasher from cabinet ...,moved out slightly....while door closed ...reached with long nosed pliers door spring pulled forward...and allowing white plastic part that fits through sleeve and fit new sleeve over it...pulled spring attaching white plastic part and pushed unit back to cabinet and replaced screws DONE.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Make sure you order 2. One on each side

Shut off breaker. Took off front skirt of dishwasher .
Used pliers to loosen the pressure clamp on drain pump , have towel handy as there will be some water. Turn pump to left as you push in on the clip on side of drain pump. It will come out. Remove wire plug from old pump and plug into new pump than insert new pump and turn and push in till it clicks. Use pliers to pinch hose clamp and push hose onto pump release hose clamp. Turn breaker on. Run a cycle and make sure all is tight before putting skirt on front.

Unscrewed the top of the dishwasher from the counter top and slid the appliance out part way in order to reach the door spring. I loosened he spring from the bracket then slid the sleeve over the bracket. I reattached the spring to the bracket, slid the dishwasher back in and screwed it to the top just like it was prior to removal. Easy as pie.

This procedure assumes that the DW water connection and drain are flexible. Remove Phillips head screws (2) mounting top front of DW to underside of counter. Grasp door and gently coax DW outwards approximately 1 foot. WEAR SAFETY GOGGLES. On RHS check lower end of door spring and note in which notch the spring sits. On RHS, grasp white plastic connector ("hinge bushing", with spring looped around one end), stretch the spring while carefully lifting other end of connector up, out of slot in door hinge lever. Pry door hinge lever 1/8" away from DW body while sliding friction sleeve over its end. Work friction sleeve past hinge hook, past wider section, into narrower slot (about 2" from end of hinge hook). Raise door to closed position. Insert and hold lower (90 degree) end of spring into the same notch that it was originally in (mine was in the 5th from the front). Loop the door end of the spring into one end of the white plastic hinge bushing, then insert the other end of the bushing into the door hinge lever's hook while stretching the spring. It does not require much strength. CAUTION: If the lower end of the spring is not properly inserted and held in the notch, it can pop out and possibly injure you! Repeat for the LHS. Push the DW back in place, and reinstall the two mounting screws.

Looked at other side of top rack which still had the stop. Just had to orient the direction of the stop and push it firmly onto the rack arm. Took a couple tries, but it went in and locked. Works perfectly. Inexpensive and easy fix to to very annoying problem.

I unscrewed the dishwasher from the counter (two screws under the countertop), and pulled it out about a foot so I could access the friction sleeve. I used a needle nosed pliers to slip a spring latch off the door. Then I slipped the new friction sleeve on and reattached the spring. Tested the door. Success! Super easy. About 5 minutes of work.

Installed new pump from the front. Power off remove front cover reached my hand behind pump for release clip, push down turned counter clockwise pump comes out. Disconnected electrical plug attached plug to new pump. Put pump in at 45 degrees rotated clockwise until hear clip lock in . Tested then replaced cover

Located drain pump under dishwasher disconnected electrical from wall and pump twisted pump to remove, and installed new pump. Great customer service from Parts Select, helped to make sure i was ordering the correct part.

1. Shut off water valve
2. disconnect water hose(wrench-adjustable)
3. Disconnect drain hose (screwdriver)
4. Pull dishwasher out from under counter
5. Put down towel to soak up residual water that drains out of dishwasher
6. lay dishwasher face down; electronics is located underneath dishwasher.
7. locate faulty drain pump
8. remove electrical connector from drain pump by first pressing on connector retention tab with screwdriver while sliding connector loose.
9. twist drain pump body while using screw driver to depress drain pump retention tab.
10. remove old drain pump body and insert and twist new drain pump body into old location (use screw driver to assist retention tab engagement)
11. attach electrical connector.
12. Return dishwasher to upright position, slide it under the counter (with its cotton cover); reconnect hoses AND turn water supply back on (make sure you remember to turn the water supply back on)

You only need to pull it out about 6 to 8 inches and you don’t need to disconnect anything to slide it on

Snapped the new stops on. It took about 2 minutes.

Removed the bottom plate/cover. Unscrew top from bracket. Lucky,had just enough room to pull washer out. Only 6 in. Sleeve had broken off. Needle nose plyers to unhook spring. Slide sleeve over hinge. Hard Part///. Pull spring back into place. with door shut. good luck.

First I got online to troubleshoot issue to save mysel from a service call. One of the first UTube videos, a young man said usually the main issue was the lever. He pushed down on the floater. If it didn't click, than the lever below needed to be replaced. Most important to turn off the circuit breaker before beginning the repair. I got on whirlpool.com, Part Select, ordered the lever, which was under $10. And once delivered, was able to switch out the old lever with the new replacement. Part Quote video took me through the process step by step. The lever package was marked that usually it was only 2% of the time that replacing the lever fixed the issue. Of course, I was thrilled, my dishwasher was up and running again. Thank you.