Models
>
2213804N710
2213804N710 Kenmore Dishwasher
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
This is a single rack track stop clip used to prevent the upper dish rack from sliding all the way out of the dishwasher. It is made of gray plastic and can wear with time. This is an easy repair that...
In Stock
Order now and your part arrives by Aug 28
The friction sleeve, sometimes called a friction pad, is made of a flexible black plastic and measures a bit over one inch in length. It is designed to reduce the friction between the hinge and the do...
In Stock
Order now and your part arrives by Aug 28
$24.15
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
In Stock
Order now and your part arrives by Aug 28
In Stock
Order now and your part arrives by Aug 28
$66.86
This genuine drain pump motor assembly plays a vital role in your dishwasher’s operation by removing water from the tub during the drain cycle. If you're experiencing drainage issues, leaks, or poor c...
In Stock
Order now and your part arrives by Aug 28
$22.91
Includes power cord and all necessary parts needed for complete installation of cord.
In Stock
Order now and your part arrives by Aug 28
$72.17
This is connected to the water valve, is located on the side of your tub and allows water to enter your dishwasher.
***Note: This part does not include the inlet gasket - must order separately.
In Stock
Order now and your part arrives by Aug 28
In Stock
Order now and your part arrives by Aug 28
In Stock
Order now and your part arrives by Aug 28
In Stock
Order now and your part arrives by Aug 28
In Stock
Order now and your part arrives by Aug 28
Special Order
Common Problems and Symptoms for 2213804N710
Viewing 9 of 9Not draining
Fixed by these parts
How to fix it
Door latch failure
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Not cleaning dishes properly
Fixed by these parts
How to fix it
Will not fill with water
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Will not dispense detergent
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Arthur from YORKTOWN HTS, NY
- Parts Used:
- WP8268961
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door will fall down after opening
unscrewed dishwasher from cabinet ...,moved out slightly....while door closed ...reached with long nosed pliers door spring pulled forward...and allowing white plastic part that fits through sleeve and fit new sleeve over it...pulled spring attaching white plastic part and pushed unit back to cabinet and replaced screws DONE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from PALM BAY, FL
- Parts Used:
- WP8268961
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Friction sleeve
Make sure you order 2. One on each side
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelli from BURLINGTON, MA
- Parts Used:
- W10876537
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Dish washer would not drain properly
Shut off breaker. Took off front skirt of dishwasher .
Used pliers to loosen the pressure clamp on drain pump , have towel handy as there will be some water. Turn pump to left as you push in on the clip on side of drain pump. It will come out. Remove wire plug from old pump and plug into new pump than insert new pump and turn an ... Read more d push in till it clicks. Use pliers to pinch hose clamp and push hose onto pump release hose clamp. Turn breaker on. Run a cycle and make sure all is tight before putting skirt on front.
Used pliers to loosen the pressure clamp on drain pump , have towel handy as there will be some water. Turn pump to left as you push in on the clip on side of drain pump. It will come out. Remove wire plug from old pump and plug into new pump than insert new pump and turn an ... Read more d push in till it clicks. Use pliers to pinch hose clamp and push hose onto pump release hose clamp. Turn breaker on. Run a cycle and make sure all is tight before putting skirt on front.
Read less
Was this instruction helpful to you?
Thank you for voting!