2213479N413 Kenmore Dishwasher - Instructions

Very simple to repair The front track stops just slide into place, easy. When I looked for these parts this place was the least expensive and the quickest delivery I have ever had. Quick, efficient and friendly online staffing. Thank you, Deb

Took off the old bracket with a screwdriver. Replaced with new bracket.

1. Moved dishrack and tracks outward then moved just the dish rack only in. 2. Using screw driver, pushed plastic tongue on end cap at track and lifted off the end cap. Repeated procedure on second track on opposite side of dish rack. 3. With end caps removed, pull dish rack out and place on table. 4. Examine each track and remove any pieces of broken wheel mounts. 5. Install new wheel mount on opposite side of dish rack from good wheel mounts. 6. Slide dish rack back in place with all four wheel mounts inserted in the two tracks. 7. Reinstall the end caps on the tracks and the fix is done.

Took out racks. And releaseed bar. Released set screws and gentley pulled out unit to expose 5/16th nuts. Removed nuts and cleaned area. Used old gaskets as the new part did not come with the gaskets, Screwed in nuts. Reset bar and set rack on carriers.

based on advice here, concluded the problem was likely that the part "Valve-Inlt" was defective. Our dishwasher intake line is copper and had already developed a partial kink from sometime in the past, so I had to be careful. The final connection to the new part had to happen in place: very close to the floor and underneath, because I didn’t want to stress the copper line. Plus, the shutoff was defective, and it was always leaking while I connected. Awkward. As I was threading on, it started to look like it might be cross-threaded, so I stopped and reversed. Slid the washer back out and disconnected the drain line so I could tip the dishwasher u and inspect. It was going on cross-threaded. Not hard to happen on a metal to a plastic connection. To solve, I carefully made very small bends in the copper inlet line until when it would later be brought up underneath to connect to the inlet valve, it would be as perfectly aligned as possible. This worked. As I tightened, it went a little easier and the leak stopped. A good moment. Tightened a bit more, but didn’t want to overdo it as that can cause other problems. Now the moment of truth: let’s run it. DISHWASHER WORKED AGAIN. Runs fine now and we are glad to have it back. Was satisfying I could do this on my own. The advice and guides here made that possible. Thank you.

Replaced wheels easily

I'm the maintenance supervisor at an apartment complex. While installing a new dishwasher for a tenant, I inadvertently cross-threaded the swivel connector to the fill valve. The valve was ruined and couldn't be repaired. I ordered a new valve (it was an OEM) and installed it. Simple switch out, plus the video from Parts Select showed I had done it right.

just replaced broken piece ,,,, very easy ,,, will use you again for parts should the need arise

Popped off the side stay on the rack, slid the new part on the rack and snapped it into position. Replaced the side stay on teh runner. Done!

The repair was very, very easy. The only tool I used were my fingers. Took me about 2 minutes. Would have been less but I forgot to remove the broken wheel before installing the new one so I had to repeat the process. This hardest part was removing the end piece from the rail. If you look closely there is a little tab that needs to be pushed forward to remove the end piece. Once that is done it's very easy. I'm sure I saved $100 vs calling a repair person. I actually purchased 2 replacement parts in anticipation of another one breaking.

Well, it’s very easy to repair. But, what I like if ur Company is, the availability, of the parts.
Thanks you.

Tipped over washer, removed attachment bolts, installed new pump by clamping water hoses. Be sure to use proper crimping pliers, not the generic slip joint pliers. Replacement pump included required new clamps.

Watched video, removed the door gasket and replaced

As stated above the repair did not go well because the gasket was too wide and the door would close. Suggest you talk with Whirlpool about the part they sold you for my model of dishwasher.

I followed installation instructions from this site and all went well.