6651588583 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ronald from VAN BUREN TWP, MI
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
none
removed and installed cords with screw driver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Terryville, CT
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacement of lower rack wheels (rollers)
This job took 30 seconds to accomplish. The old wheel assemblies (4) just snapped off and the new wheel rollers just snapped in their place. No tools were needed. Extremely satisfied with this product. Wished I had performed this repair years ago!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lance from Hayward, CA
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I had a broken lower rack wheel
I simply snapped off the old broken roller set and snapped on the replacements. No tools were even needed and now the rack rolls smoothly on all wheels! This has encouraged me to try other
repair projects.
repair projects.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phil from Ft Lauderdale, FL
- Parts Used:
- 675611
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
1 spring broke
removed the 2 screws that hold in the washer, pulled it out, with the door shut, removed and replaced the remaining spring , then went to the other side and did the one that broke off. then I reinstalled the unit. simple !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from BRUSH PRAIRIE, WA
- Parts Used:
- 675611
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Replaced broken door spring
This repair should have been rated "Easy" but because of a) the age of the dishwasher - 25 years and b) the close quarters to replace the spring, it was a bit of a challenge. If I could have pulled the dishwasher out a few inches, replacing the spring would have been a snap. But because of new flooring on top of existing flooring, that wasn't possible. Also the side cabinets were so close that getting a pair of pliers in there to hook the spring onto the door was tough. Ended up cutting out some cabinet facing that wasn't going to effect the look of things in order to get my hands and tools in there to get the hook end of the spring on the door. After I finally got it on and replaced the kickplate, sat back and had a cold one. Whew!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elmer from YORKVILLE, IL
- Parts Used:
- 675806
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
1/4 inch bolt frozen to shaft
The 1/4 inch impeller bolt to shaft would not budge with a nut driver so I had to use a ratchet to loosen it. I could not hold the drain impeller with an adjustable wrench so I had to use a vice-grip. This still did not loosen it so I used an oscillating power saw to cut away at the bottom of the drain impeller being careful to only cut so deep, I didn't want to cut into the motor shaft. Once I had cut some grooves into the drain impeller, I could break it into pieces and remove it. Upon reassembly I tightened the 1/4 inch bolt with the ratchet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from IONIA, MI
- Parts Used:
- W11169039
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
cut wire in center sprayer to remove plastic holder for new basket
after that every thing went very well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from SICKLERVILLE, NJ
- Parts Used:
- 4317824
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Intermittent power loss
Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claiborne from Atlanta, GA
- Parts Used:
- 675611
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Both Dishwasher door springs broken
Pulled out the DW and removed old spring parts. Used screw driver and pliers to respring
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Hialeah, FL
- Parts Used:
- 675611
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
left door spring broken - door wouldn't stay up
Removed the two screws securing the dishwasher to the underside of countertop.
Pulled the washer out until the spring mechanism was visible. Vacuumed the area - it was filthy. Assembled the spring and adjusting hook. Took me 4 tries to get the spring into the proper tension slot. Having the other side intact helped in understanding how it worked. Used long nosed pliers to bring spring onto the door retaing plate slot after trying unsuccessfully with regular pliers.
Pulled the washer out until the spring mechanism was visible. Vacuumed the area - it was filthy. Assembled the spring and adjusting hook. Took me 4 tries to get the spring into the proper tension slot. Having the other side intact helped in understanding how it worked. Used long nosed pliers to bring spring onto the door retaing plate slot after trying unsuccessfully with regular pliers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Shreveport, LA
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Replaced four lower rack on a whirlpool dishwasher.
I prayed old wheel assembly’s off with the claw end of a claw hammer. Carefully snapped on the new assembly’s which were a little tricky to align. Went well, took about 15 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from GREENVILLE, MI
- Parts Used:
- 4317933
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
all of the old rollers were missing.
the design of the new roller kit was a little different than the original. took a minute to figure the installation. all went well. the new roller assembly fit the 30 year old dish rack
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from St Johnsbury, VT
- Parts Used:
- W10311986
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
lower rack started to rust through coating
Since there were no printed instructions, we looked at the photo schematic.
Reassembly using the photo was easy by putting the old rack alongside the new one and adjusting the new rack spacing to match the old one.
We also had new wheels which snapped on.
We were delighted to repair and replace this good, older dishwasher rather than purchase a new one!
Reassembly using the photo was easy by putting the old rack alongside the new one and adjusting the new rack spacing to match the old one.
We also had new wheels which snapped on.
We were delighted to repair and replace this good, older dishwasher rather than purchase a new one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- B Jean from MONTPELIER, OH
- Parts Used:
- WP302711
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
throwed water out under the door
Did not use the new parts. After removing the spray arm, found a screw out of place. Put the seal ring back in place and the screw back in the hole. Machine works like new.
Was this instruction helpful to you?
Thank you for voting!
Lack of assembly instructions
YouTube was very helpful
New racks works better that way expected. Rearrange ment maximized loading
New racks works better that way expected. Rearrange ment maximized loading
Was this instruction helpful to you?
Thank you for voting!