6651644590 Kenmore Dishwasher - Instructions

Opened the door removed old seal and put the new one in. The only hard part was getting the new seal out of the package. It took about 1 minute to do. Very easy.

Amazing how quickly the part was shipped and arrived. Very easy to install no tools needed.very pleased with everything . Thank you.

Replacing the cup latch and dispenser cover was pretty easy. First, I removed the inside cover of the door of the dishwasher. Then I carefully removed the plastic covers/slides on the door, removed the broken cup latch and then inserted the new one. Replaced the plastic covers/slides, the reinstalled the inside cover on the dishwasher. Next, I removed the dispenser cover and installed the new one. It snaps off/on, by the way. It only looks like it slides on/off.

Took inside door panel off. replaced spring that opens soap dispenser lid during cycle. Put inside panel back on. Works fine now.

I installed the opener spring in the direction it was needed to open the door then installed the pin. I placed the door in the position it goes and took a pair of pliers and squeezed the pin into the pin slot. the spring has to be forced into a tension position. I did this by sliding the spring to one side and forcing it into position, the other side is done the same way. works great

Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install

The top of the latch was broken on I had to push the plunger back through the mounting to get it out. ai had to pull the whole assembly apart to get the locking nut out. i remove the latch assy and took about 10 minutes to figure out how to put it back together. Changing it with the help of the video wasn't hard but confusing at times. Thanks for the video.

Followed vidio instructionson web site. Quick easy fix

I watched the video that you had on line and the repair was done in a snap. The shipping was fast also.

we followed your instructions submitted via e-mail and they worked out just fine....thank you

Got on the computer, located your site and read the repair stories.Thought, I can do this. Ordered the impeller and seal kit. I followed the same procedures as your other customers, however, when I turned it on for a test it still leaked. Went out looked for a new dishwasher, for $389.00. After talking to my wife,(been married over 60 years)decided to try one more time. Went through the same steps. Loosen the plastic ring remove The revolving spraying arm, tipped on the front to get to the bottom. mopped up the water,disconected water, electric, and hoses. Pulled the motor and pump unit, disassembled the pump unit,then I realized I had installed the rubber and plastic bearing backwards. The rubber to rubber wore out real fast. Ordered a new seal kit (no impeller) Put it all back together and it works just like it did 19 years ago. Total cost less than $60.00. It is a good feeling when your able to fix somthing like this, especially ehen your a fat 83 year old. I would like to meet the person that changed this in a half hour.

I ordered door cover kit #4387043. It comes with new door cover (lid), new pin, spring, latch and snap. Two problems I encountered was 1)with the spring - there is a trick to replacing it. I had to look up how to put the spring on properly. Go to YouTube and Partselect "Dishwasher Repair - Replacing the Lid Spring (Whirlpool Part # 8066018) " will show you the trick. Was a cinch after I knew the trick. 2) you must take door apart to replace snap that goes with the latch, so you might want to replace the detergent door first and see if that solves your problem without changing the latch. It is workable, but I had to go on line and look for diagram to put back together. Just frustrating but for less than $20.00 solved the problem. Good luck.

Started down Parts Select list of possibilities. Replaced the door gasket (1/2 hour), still leaked. Replaced water deflectors (15 min), still leaked. Was looking at steam vent and read the repair submitted by "mary from Fountain Green UT". Removed and thoroughly cleaned the steam vent (1/2 hour). Stopped leaking and is working fine now. Repairs were very easy using Parts Select instructions.

The repair was very simple. Simply pull the dishwasher out far enough to access the springs, remove the old with pliers and install the new springs in the same spot as the old ones.

Bought a house and with it can an old whirlpool dishwasher in where the soap dispenser lid would latch, as the latch itself was gone. Ordered the latch from part select and used the installation video to switch the latch out. Only problem I came across was that the torx screws at top of he door were free spinning. Ended up using a flat head for leverage to finally get the screws out. Everything works perfectly for once.