66513479N413 Kenmore Dishwasher - Instructions

1. Open dishwasher door, to access the screws holding dishwasher to cabinet.... remove these screws.
2. May need to shut water off and unscrew water line and waste line (if they aren't long enough because you will need to pull dishwasher out.
3. Unplug electricity
4. Pull dishwasher all the way out... probably need to disconnect the water and waste lines
5. crescent wrench to unscrew the plastic screws in back
6. Disconnect two wires going to element
7. Replace element... reverse steps
8. Not too bad at all
9. Part Select is Awesome !!!!

Replaced the pump.That wasn't the problem --- if I had it to start over, I'd pull the drain hoses and run the dishwasher to see what water is flowing where. I had a clogged drain --- and maybe something else. Still working through the details.

Snapped off old plastic wheel units and snapped new one one and finally put it back onto the track

Removing and installing the new part was fairly simple. We removed the water hose first since it is the easiest to see. We then removed the screw holding the part to the metal frame. We slid out the part out of the holder to remove the black hose and electric plug (it is like the old phone jacks). After it was completely off we plugged in the electric to the new part which was very easy since it can only go in one way. We slid the new part in place and attached the black hose. We attached the piece to the frame with the one screw and last we attached the gold (garden hose) connection. We turned on the water to look for any leaks then turned the power on and ran it through a partial rinse to be sure there were no leaks.

removed unit from cabinet disconnected water and drain lines replaced heater very easy to do it took more time to remove unit from under counter than replace heater piece of cake..

Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!

Our dishwasher's top rack would pull too far out which made it hard to stay in alignment. It had lost it's track stop. I easily ordered the part from PartSelect, and it came more quickly than I expected; I clicked it in place and it runs like new. It's wonderful to deal with a company that knows the frustration of not having your appliance in good working orfer.
Thank you.
Sue M
Masdsachusetts

Very simple to repair The front track stops just slide into place, easy. When I looked for these parts this place was the least expensive and the quickest delivery I have ever had. Quick, efficient and friendly online staffing. Thank you, Deb

Watched YouTube first of course. Pulled off the old gasket, found the center of the new gasket and started installing the gasket from the very top and all the way down the sides. I made sure it was in tightly and smooth. No more leak, should have listened to my wife sooner!

Replaced wheel part. EXPZ.

The hardest part was squeezing the tab at the end of the track to pull it up and out so that the old wheel part could be slid out and the new one in. Fortunately, the track is open on the side facing the interior of the dishwasher so you can see what you're doing. Once that was done, it was simple to snap the new part into place, slide the wheel into the track, and replace the tab at the end.

Took off the old bracket with a screwdriver. Replaced with new bracket.

Popped off the side stay on the rack, slid the new part on the rack and snapped it into position. Replaced the side stay on teh runner. Done!

The repair was very, very easy. The only tool I used were my fingers. Took me about 2 minutes. Would have been less but I forgot to remove the broken wheel before installing the new one so I had to repeat the process. This hardest part was removing the end piece from the rail. If you look closely there is a little tab that needs to be pushed forward to remove the end piece. Once that is done it's very easy. I'm sure I saved $100 vs calling a repair person. I actually purchased 2 replacement parts in anticipation of another one breaking.

Ordered part; took part out of box when it arrived; took broken part off; put new part on. No tools needed.