6651560592 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeff from BRUSH PRAIRIE, WA
- Parts Used:
- 675611
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Replaced broken door spring
This repair should have been rated "Easy" but because of a) the age of the dishwasher - 25 years and b) the close quarters to replace the spring, it was a bit of a challenge. If I could have pulled the dishwasher out a few inches, replacing the spring would have been a snap. But because of new flooring on top of existing flooring, that wasn't possible. Also the side cabinets were so close that getting a pair of pliers in there to hook the spring onto the door was tough. Ended up cutting out some cabinet facing that wasn't going to effect the look of things in order to get my hands and tools in there to get the hook end of the spring on the door. After I finally got it on and replaced the kickplate, sat back and had a cold one. Whew!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aubrey from BERKELEY LAKE, GA
- Parts Used:
- 675806
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
The Cutter Spring was totally disfigured and pulled apart. Not functional.
Repair went exactly like the video i watched online. Perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from JUPITER, FL
- Parts Used:
- W10311986
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
THE LOWER RACK WAS CORRODING IN SPOTS AND WAS RUSTING
THERE WERE NO INSTRUCTIONS INCLUDED, COULDN'T FIGURE 0UT HOW TO INSTALL THE NEW ROLLERS ON THE NEW RACK FINALLY INSTALLED THE OLD ROLLERS ON THE NEW RACK AND THEY WERE MUCH EASIER TO INSTALL I DONT UNDERSTAND
WHY THE NEW ROLLERS WERE THE SAME AS THE OLD ROLLERS
EXCEPT FOR THE COST.
WHY THE NEW ROLLERS WERE THE SAME AS THE OLD ROLLERS
EXCEPT FOR THE COST.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Peoria, AZ
- Parts Used:
- W10311986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
original dishrack had become rusty
installed a new rack
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from HOUSTON, TX
- Parts Used:
- WP717273
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dishwasher Not Heating top rack wet dishes and heating rod looks rusted
It took all of 30 minutes from beginning to end remove the old parts and replaced them and run a diagnostic test before I could wash dishes. The parts were exact and Parts Select has always provided the right parts, shipped fast and never disappointed me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Rochester, IL
- Parts Used:
- W10311986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Rack Was Rusting Out
Kit didn't have the center conical piece. Easy to switch tho. I am impressed at the speed of which the part arrived.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from KINGSPORT, TN
- Parts Used:
- 675806
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
i had a leak under the dishwasher when the pump turned on.
I replaced the seals per the video instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from BROKEN BOW, NE
- Parts Used:
- 675611
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Wrench (Adjustable)
the left door spring broke, but we were able to use the dishwasher.
I called to order two springs and your salespersons were very helpful. The two springs were sent immediately. my husband pulled out our under-the-counter dishwasher and replaced both springs within 30 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from ELGIN, IL
- Parts Used:
- W10311986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
my old lower dishwasher rack was rusted out and some parts broken.
Snapped on the rollers, removed the center part from the old rack that sprays the water and snapped it on the new one. We then bent the back row down so it would acomodate my larger items. My old rack had that feature. You could either have the rack up or down. Now l
ooks beautiful and works perfectly.
Could have used some directions though.
ooks beautiful and works perfectly.
Could have used some directions though.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from LEVITTOWN, PA
- Parts Used:
- WP302868
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lost Screws from lower access covers for my Dishwasher
Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from JACKSONVILLE, FL
- Parts Used:
- W11169039
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Upper dish rack broken tines
Swapped out the old upper dish rack with a new one. A video made the change simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Dubuque, IA
- Parts Used:
- WP8066018
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
soap dish door does not always pop open
the plastic pin that retains the spring has a head on one end that hits a plastic stop on the door to keep it from coming out. I used a small grinder and made a flat spot on the head diameter to make it easy to slide out. This is easier than trying to pry the door off the pin at the two retaing snaps. I was conderned these pin retainer clips were brittle and would break off.
Once the pin is slid out, it is a matter to hold the new spring holes in line with the pin. rotate pin so flat side you ground is turned up, so pin will not move out that way. Tiij about an hour
Once the pin is slid out, it is a matter to hold the new spring holes in line with the pin. rotate pin so flat side you ground is turned up, so pin will not move out that way. Tiij about an hour
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricker from KESWICK, VA
- Parts Used:
- 675806
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
noisy
watched a video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Dayton, TX
- Parts Used:
- W10311986
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Dishrack Tines were breaking off due to age
The rack came with pictorial instructions which were fairly veg, however they were to the point. The wheels snapped into place easily, and the center water transfer tube twisted off the old one and twisted on the new one just fine. It is a very good idea to keep the old one out to look at as a guide. There were no instructions on how to remove the transfer tube, I was lucky to have already worked on these before. After that it fits and works just peachy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- karen from Galloway, NJ
- Parts Used:
- 675611
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
old spring broken
after figuring out how to position the door the instructions were good
Was this instruction helpful to you?
Thank you for voting!