19985 (1988) Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Darrel from rosamond, CA
- Parts Used:
- WP8066018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lid Spring
Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Columbia, MD
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Soap cup latch was broken and dispenser cover was worn.
Replacing the cup latch and dispenser cover was pretty easy. First, I removed the inside cover of the door of the dishwasher. Then I carefully removed the plastic covers/slides on the door, removed the broken cup latch and then inserted the new one. Replaced the plastic covers/slides, the reinstalled the inside cover on the dishwasher. Next, I removed the dispenser cover and installed the new one. It snaps off/on, by the way. It only looks like it slides on/off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Alton, IL
- Parts Used:
- 675611
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
One spring on a dishwasher door was broken
I simply looked at the remaining spring to see which notch it needed to be attached to. I went in very well using a long needle nose plier. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Trafalgar, IN
- Parts Used:
- WP302711
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishes not clean and soap dispenser not completely rinsed out.
I looked in the bottom of the dishwasher after browsing the website regarding possible solutions. When I removed the bottom spray arm I noticed three screws missing from the pump housing. The loose pump outlet had allowed the seal to push out. Ordered-Normal shipping on the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greta from Benbrook, TX
- Parts Used:
- 4387043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
detergent door was not opening during wash
I ordered door cover kit #4387043. It comes with new door cover (lid), new pin, spring, latch and snap. Two problems I encountered was 1)with the spring - there is a trick to replacing it. I had to look up how to put the spring on properly. Go to YouTube and Partselect "Dishwasher Repair - Replacing the Lid Spring (Whirlpool Part # 8066018) " will show you the trick. Was a cinch after I knew the trick. 2) you must take door apart to replace snap that goes with the latch, so you might want to replace the detergent door first and see if that solves your problem without changing the latch. It is workable, but I had to go on line and look for diagram to put back together. Just frustrating but for less than $20.00 solved the problem. Good luck.
Was this instruction helpful to you?
Thank you for voting!