6651580590 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Donald from Albuquerque, NM
- Parts Used:
- 3367910
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Gasket around nozzle cap wouldn't stay on - in two pcs.
As there was not a replacement gasket listed in the parts lists or schematics, I ordered the entire nozzle cap hoping the gasket would come with it. It didn't so I glued the gasket in place and installed the new cap. I also replaced the washer arm bearing while I had the cap off. I am hoping the nozzle stays in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Columbia, MD
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Soap cup latch was broken and dispenser cover was worn.
Replacing the cup latch and dispenser cover was pretty easy. First, I removed the inside cover of the door of the dishwasher. Then I carefully removed the plastic covers/slides on the door, removed the broken cup latch and then inserted the new one. Replaced the plastic covers/slides, the reinstalled the inside cover on the dishwasher. Next, I removed the dispenser cover and installed the new one. It snaps off/on, by the way. It only looks like it slides on/off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Ritzville, WA
- Parts Used:
- WP302711
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
leaking badly & not cleaning dishes
You need a properly sized hex (Allen) wrench to get the screws out. Basically simple: remover bottom roller tray, unscrew large plastic holding bolt, remove lower spray arm, unscrew bolts (be sure the wrench is sized right or you might strip the heads), and replace gasket; then reverse procedure. Chances are if the gasket was bad, it will be very obvious (out of circular slot and stretched).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Sebring, FL
- Parts Used:
- 4387043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Detergent door would not spring open-spring was broke
Put on new door, making sure the spring was set to flip the detergent door open in order for the detergent to properly do the dishes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Tucson, AZ
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wheels on Rack Needed to be Replaced
A VERY easy repair! I simply pried off the old wheel assemblies with a screw driver and popped on the new ones. I was a little concerned about the new ones fitting correctly as the dishwasher is over 25 years old, but after a week they still work fine. An easy fix to an annoying problem....wish I had ordered these ages ago! Bottom rack of my dishwasher now rolls in and out like new (instead of the the few remaining wheels constantly falling off!) Very happy I ordered these and delivery was quick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve J from Brookville, IN
- Parts Used:
- 3367910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rubber on the nozzle cap fell off
Unscrewed the old one and replaced it with the new one. My wife actually ordered this Pat and repaired the dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Powell, OH
- Parts Used:
- 675238
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Dishwasher wouldn't drain
Turn off the breaker to the dishwasher - there will be water very near the motor and other electrical components. I first scooped and towelled all the water out of the bottom of the dishwasher. The drain valve can be accessed from the bottom front of the dishwasher without pulling the unit out from under the counter. There were 4 screws to remove the 2 bottom metal panels. Next use pliers to loosen and slide back the hose clamp connected to the drain. Have a towel ready and pull the drain hose off the white check valve. The check valve can then be removed by unscrewing it - you may need to use pliers. Put the new one on and everything back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delano from Durham, NC
- Parts Used:
- 4387043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
spring on dispenser broken
Removed cover and broken spring ,installed new spring and cover.Did it all in less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Del Mar, CA
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the rollers were completly broken off & I had to lift the bottom tray in/out of the dishwasher
popped off the old rollers + tracks; then snapped on the new ones; as my granddaughter would say "easy peasy lemon squeezy". Took hardly any time at all. :-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- perry from cynthiana, KY
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
detergent dispencer door spring and pin worn
I installed the opener spring in the direction it was needed to open the door then installed the pin. I placed the door in the position it goes and took a pair of pliers and squeezed the pin into the pin slot. the spring has to be forced into a tension position. I did this by sliding the spring to one side and forcing it into position, the other side is done the same way. works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Alton, IL
- Parts Used:
- 675611
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
One spring on a dishwasher door was broken
I simply looked at the remaining spring to see which notch it needed to be attached to. I went in very well using a long needle nose plier. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fernando from El Paso, TX
- Parts Used:
- 675806
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Dishwasher making a noise (lower area)
I reviewed your video and followed the steps, I appreciate the video. I used the tools described in the video; it was a simple process. Thank you Parts Select. .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Trafalgar, IN
- Parts Used:
- WP302711
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishes not clean and soap dispenser not completely rinsed out.
I looked in the bottom of the dishwasher after browsing the website regarding possible solutions. When I removed the bottom spray arm I noticed three screws missing from the pump housing. The loose pump outlet had allowed the seal to push out. Ordered-Normal shipping on the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudia from Alexandria, VA
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rollers were broken on original parts
Unsnapped the old rollers and snapped in the new ones. Worked great and easy. I was very pleased that the parts came so soon as well. Thank You, Ms. Cason
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Arlington Heights, IL
- Parts Used:
- 675806
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Leaking seals
Used the diagram and disassembled and reassembled.Used most parts that were in kit as it also fit other models and did not need all the parts.
Was this instruction helpful to you?
Thank you for voting!