66516474300 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Beaufort, SC
- Parts Used:
- 8269144A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Drain hose leaking
I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.
Was this instruction helpful to you?
Thank you for voting!
Pan leaked at the float/switch penetration
1. do not order or buy anything before examining the tension nut and washer. 2. Unplug the unit. 3. Open the switch box before trying to remove the float. Two types; easiest is pin based and lifts out easily. If the float catches, it likely has a headed bottom and needs an assist to lift past the stop flanges. 3. Using a standard ohmmeter, check for continuity. If it checks no need to replace. 4. Check float and assembly for abnormalities; cracks, lime deposits, etc. 5. Now decide what needs replacing. Did all my work with relative ease without pulling out the appliance. A couple sequences may need realigned.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Bend, OR
- Parts Used:
- WP8269209
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No power to dishwasher. Quit mid-cycle.
Pulled front panel and replaced door switch. Extremely easy but did not fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Rockville, MD
- Parts Used:
- W10728160
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The cap of a vertical tine in the dishwasher had come off, leaving an exposed, rusted and sharp top.
The old tine row came out easily and the new one was easy to pop into place. I was pleased that it was so easy to order a replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Ann Arbor, MI
- Parts Used:
- WP8535660
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The old seal would often travel with the door when opened.
I removed the old seal and carefully cleaned the track into which the seal was fixed. No tools other than some ordinary cleaning liquid, cloth and small wooden piece to swab out the track. Easy and quick. As a note here, I first used the incorrect schematic for the unit and ordered the wrong seal. However after receiving the wrong part, I made the correction and reordered. I did this over the phone as I needed instructions to return the part. The person taking my order and answering my questions was very helpful and I want to take this opportunity to thank her.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Discovery Bay, CA
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door spring link broke.
Unplug dishwasher and slide it out from under cabinet. Remove old broken link (a heavy string between two plastic parts) and replace with new one. Slide dishwasher back and plug it in. Very easy and no tools required.
Was this instruction helpful to you?
Thank you for voting!
Noisy rattle in dishwasher since new when it was filling
Remove and replace solinoid, remove and replace mico switch. These are the only two electrically controlled devieces controling water flow. Replacing switch without replacing housing takes a soft touch. A small screw driver helps. Electrical connections have a stay in place nipple. Plyers help get thoes off.
Parts delivered as promised, correct fit. Phone contact available at order question.
Would used this site again.
grade 3.5 A=4
Parts delivered as promised, correct fit. Phone contact available at order question.
Would used this site again.
grade 3.5 A=4
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Tucson, AZ
- Parts Used:
- W11196317
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher door leaked
Just removed the old seal and followed the instructions that came with the new one. Since the old one didn't have any adhesive on it ,I didn't use the adhesice on the new one. Problem solved!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Kernersville, NC
- Parts Used:
- 8269144A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
old hose possible leakage
put new hose on, very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lisa from columbus, NE
- Parts Used:
- WPW10757217
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench set
front seal on the old pump failed causing the front bearing to get wet repeatedly and fail
Removed required hardware and dishwasher from undercounter mount. Turned dishwasher on its front and removed the old motor. Installed the new motor and tested for function. Installed once test was successful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from BILLINGS, MT
- Parts Used:
- W10727426
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
the tines in the upper basket of the dishwasher were falling apart
Removed the old tines by pushing out the clips on the end and then installed the new tines and applied clips - took 10 minutes worked slick and the washer basket looks to be brand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Conelis from Eclectic, AL
- Parts Used:
- WPW10757217
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The motor was too loud
I took the unit apart to find out what was making the loud noise and found the seal on the main pump had been leaking ito the bearing on the motor.
Was this instruction helpful to you?
Thank you for voting!
One day when opening the door there was a "Snap" and the door fell open.
I first went on line to the KitchenAid repair web site and found my problem listed and instructions given . This first of all led me to a parts drawing for my model and then to the site connection to order the parts and receive the instructions. The parts arrived quickly and the instructions were thorough and easy to follow. This was a good experience for me.
Was this instruction helpful to you?
Thank you for voting!
Door latch not working
Watch a YouTube video to replace the latch. The strike, removes easily by gently prying out with a screw driver on both sides. You do NOT have to pull out the dishwasher as some you tube videos show.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Roseville, CA
- Parts Used:
- 8193762
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishwasher died
1. Opened inside panel (about 8 screws)
2. Checked wires to see if we had power, which led me to the fuse.
3. All wires were hot, so I bypassed fuse straight to the motor, which worked.
4. Took out the fuse, didn't really know for sure whether it was bad yet, googled the part number and it led me to PartSelect.com!
5. Ordered part (it arrived in two days!) and replaced existing fuse and WE ARE WASHING DISHED AGAIN!!
2. Checked wires to see if we had power, which led me to the fuse.
3. All wires were hot, so I bypassed fuse straight to the motor, which worked.
4. Took out the fuse, didn't really know for sure whether it was bad yet, googled the part number and it led me to PartSelect.com!
5. Ordered part (it arrived in two days!) and replaced existing fuse and WE ARE WASHING DISHED AGAIN!!
Was this instruction helpful to you?
Thank you for voting!