6651597399 Kenmore Dishwasher - Instructions

replaced those parts... but lingering doubts about adequacy of water supply due to sediment primarily from old iron pipes, evidenced in faucet aerator. So I added a Rusco hot water sediment trap filter to the supply line leading to the dishwasher and faucet, along with a new flex supply line to the dishwasher. Water supply seems improved, and any potential sediment will be caught by the trap.The time, tools, and complexity of adding the hot water sediment filter are not covered in the above.

I put the bearing ring on the washer arm and then screwed on the retainer nut.
Easy to order the needed parts

This spinner is attached to a plastic module PN WP3379369 which is held in place by two screws to the top of the dishwasher. I was able to temporarily reattach the spinner by using a hot soldering iron to melt the nylon axle that goes through the spinner. By using a very small metal washer placed on top of the spinner I was able to melt enough off the end of the nylon axle so as to keep the spinner in place and still be able to rotate. By far the most difficult part of this repair is removing the two stops that prevent the upper washer rack being removed from the machine. Doing so requires using a pair of long nosed pliers and taking note of what needs to be squeezed. Even if installing a new part the upper rack needs to be removed in order to get access to this central part.

Took the old one off put the new one on

The nut had broken off even with the top of the threaded area, so we had to remove that broken part. We did so by using small pliers and inserting them in the opening and held them in a spreaded position while turning the broken piece out. We replaced the three new parts and put it back together and it works fine. So easy and much cheaper that having a repairman come in. Took us less than 15 minutes.

Once I figured it out it was not bad at all and most of all it worked, no leaks. I just cleaned some old glue off the stainless steel, dried it well, ran a bead of glue like directions showed, squeezed in the new gasket, closed the door for 24 hours then ran the dishwasher. No Problems.

I guess some food got caught in the water level sense float and caused it to mal function.
In the diagnosis process, I removed the arm to clean out any debree in the strainer ( found broken glass). I also found that the two rings mentioned above were worn. I replaced them and all is well.
Thank you for fast response with the replacement parts.

Following instructions I found on the web, I removed the bottom plates of the dishwasher and could see the broken spring hanging from its attachment point. After shutting the power off, I reached in, removed the broken spring and with a bit of muscle, attached the new spring and stretched it to a bracket that gave the door stability when openeed. Took about 20 minutes to finish up and the door works nicely. Saved a ton of money versus calling in a repair man at $90 for arriving and $30 each 15 minutes

First I removed the upper basket from the dishwasher by taking off the end clips from the right and left hand slides. The clips are removed by prying them gently upward with a screwdriver.

Second I removed the old spray arm assembly by slipping the old tube off of the rotary fitting.

Third I removed the center screw from the rotary fitting which holds the upper spary arm in place. I also removed the small plastic piece (block) which is clipped to the wire basket.

Fourth I installed the new spray arm assembly making sure to orient the plastic spacer block so that the spray arm rotates freely. The spacer block clips on the wire tray and the assembly is held in place with a single screw.

The new assembly includes a one piece extension tube and end funnel so it is really easy to install.

Used nut driver to remove old spray arm assembly on top rack. Reinstalled the new assembly, clamped the holding assembly onto the rack, tightened the holding assembly--that's it.

Cleaned area, applied sealant and laid the sealant in. Unfortunately, it did not work. Still leaks. Going to the maytag store to get another and try again.

used a screw driver, removed 2 screws, removed broken piece, screwed in new part ....all done :)
took less than 15 minutes to do*

i just wanted to let everyone know..I ordered the part on a monday and received it on wednesday I was amazed...the part fit perfectly ...and was very easy to install myself....ty so much ...

Removed spray bar by removing the plastic finger thumb screw and replace as shown by you web page. Very simple.

The first part we had ordered was incorrect. When we called the company, the person was very helpful, and understanding. The correct part was reordered and easily installed, after the old gasket was removed. The gasket area was cleaned and installation was as simple as the video. Thank You

It was very simple, the repair took less than 5 minutes start to finish. I removed the top dish rack, took out two screws and the broken part slipped right off the water feed tube. I slipped the new upper wash assembly on the end of the tube and replaced one screw. My dishwasher is an older model and the new part only has a hole for one screw but I cannot tell any difference in stability or performance. I put the top rack back on and the dishwasher is as good as before.